Millwright Bundle Exam Questions With Verified And Updated Answers

Millwright Test Exam Questions With Verified Answers 2024/2025 If the seal was not properly aligned or there is excessive wear in some bearing or shaft______ wear tracks will be the indicator. - answerUnusual For removing hard to remove gasket materials found on sealing surfaces ______ is recom...

Millwright - Rigging and Hoisting Exam Questions With Verified Answers 1. Of a block and tackle with five rope falls and minimum friction, how much force is needed to retain 250lbs? a. 50 lbs b. 100 lbs c. 250 lbs d. 75 lbs - answera. 50 lbs 250lbs/5 = 50 lbs 2. What diameter rope is neede...

Millwright Red Seal Study 1 Exam Questions With Verified Answers Which of the following best describes a free flow control valve? A) It is the simplest form of directional control allowing flow in one direction only B) They are used to prevent a load suspended by a cylinder from free fall C) Th...

Millwright Period 4 Exam Results Questions With Verified Answers Engine Block Rejection - answerMost common reason: cracks after cleaning and inspection. Steam Turbine Class - answerRated up to 700 psig and 399°C: class 3 turbine. Gas Turbine Seals - answerUsed on compressor and turbine: labyri...

Millwright 1 Exam Questions With Verified Answers What are the 2 classes of hydraulics? Hydrostatic & Hydrodynamic What causes pressure drop in a hydraulic line? Excessive Fluid Velocity What causes aeration in a hydraulic pump? Air in the suction line What type of hydraulic cylinder is indi...

Millwright Level 1 Exam Questions With Verified Answers On a pedestal grinder, the gap between the grinding wheel and work rest should not exceed: - answer1/8 inch The kind of abrasive material used in grinding wheels for general purpose applications is: - answeraluminum oxide A blotter is use...

Millwright Test Practice 1 Quizlet Exam Questions With Verified Answers Other than scraping what other uses can a three-sided scraper be used for? - answerDeburr Holes What is a cape nose chisel used for? - answerCut grooves such as keyways What should you do with the end of chisels and punches...

Millwright level 4 INTERNAL COMBUSTION ENGINES Exam Questions With Verified Answers Before performing maintenance on a recently run engine, you must: A) Drain all oil from the crankcase B) Check and record the hour meter C) Disconnect all electrical, close, lock, tag and purge all gas sources ...

Preventive Maintenance Millwright Level 4 Exam Questions With Verified Answers Which is not a measure of amplitude? A. displacement B. velocity C. acceleration D. Vibration D. Vibration 140. What style of maintenance involves scheduling and periodic disassembly of machines for inspection A...

Belts test - Millwright level 2 Exam Questions With Verified Answers High capacity V-Belts -Also called wedge, hi-torque, or narrow v-belts -The three sizes are 3C, 5V, & 8V. Meaning they have 3/8", 5/8", and 8/8" (1") of top width. What does 3V2550 indicate? 3/8" width and 25" pitch lin...

Millwright prep level 4 conventional alignment Exam Questions With Verified Answers When equipment is aligned, the _________ are collinear - answerShaft center lines Rotating shafts are usually aligned with the ________ in Place. - answerCouplings The two ways that a coupling must be aligned ar...

Millwright Level 4 Turbines Exam Questions With Verified Answers 2024/2025 Carbon rings are used to seal the steam within the casing of steam turbines. why is this method effective on impulse type steam turbines? A. low casing pressure B. minimal maintenance C. high shaft surface speeds D. co...

Millwright Level 4 Final Prep Exam Questions And Answers 100% Fire extinguishers involving electrical equipment have the letter? A. C B. D C. A D. B A. C A class B fire extinguisher is for? A. wood and paper fires B. electrical fires C. magnesium fires D. oil and gas fires D. oil and ga...

Millwright Level 4 Electrical Exam Questions And Answers 100% Fuses are circuit protection devices. what fuse component provides the HRC type fuse with the ability to interrupt currents up to 300,000 Amps without failure? A. very large contacts B. parallel fusible links C. sand filled D. seri...