Csap 2 Current exams study guides() all are here answered corrrectly Success Bundle!!!

Match the title to the part of Article 310. - Answer General 1 Installation III Construction II The scope of Article 310 covers fixture wires, flexible cords, and cables. - Answer b. False 310.1 Match the title with the NEC reference associated with the provisions related to use...

A conduit fitting that has been evaluated and listed to prevent the ingress of cutting fluids is marked ? . - Answer a. liquidtight Conduit fittings marked "raintight" or "wet locations" are automatically considered "liquidtight." - Answer False Which NEC articles pertain to liquid...

All circuit conductors between the service equipment, the source of a separately derived system or other power supply source, and the final branch-circuit overcurrent device defines a(n) ? . - Answer Feeder art 100 Which of the following are not considered part of premises wiring (systems), by ...

Electrical nonmetallic tubing is defined in the NEC as a nonmetallic, pliable, corrugated raceway of circular cross-section with integral or associated couplings, connectors, and fittings for the installation of electrical conductors. ENT is composed of a material that is resistant to moisture and c...

A circular mil is a circle with a circumference of one mil. - Answer False A mil foot is one foot in length with a diameter of one mil. - Answer True Which of the following would not be included in NEC Chapter 9, Table 8? - Answer c. III. and VI. III. Type of insulation used on th...

Lesson 1: Conduit and Raceway Basics - Answer 1. The metric designators and trade sizes are for identification purposes only and are not actual dimensions, as pointed out in the note to NEC ? . - Answer b. Table 300.1(C) 2. Informative Annex C is part of the requirements of the NEC. - A...

Which UL Standard is required to be used by qualified electrical testing laboratories to evaluate snap switches for electrical safety? - Answer UL 20 A motor circuit switch is generally required to be rated in ? . - Answer horsepower A general-use dimmer switch is generally only permitte...

Consider the following two code segments. Assume that the int variables m and n have been properly declared and initialized and are both greater than 0. I. for (int 1 = 0; i < m * n; i++) { S("A"); } II. for (int j - 1; j <= m; j++) { for (int k = 1; k < n; k++ { S("B...

Consider the following code segment. String str = "AP"; str += "CS " + 1 + 2; Sln(str); What is printed as a result of executing the code segment? - Answer APCS 3 Consider the following code segment. String dessert = "pie"; dessert += "straw" + dessert + "berry"; What ...

What is the minimum rating required for a receptacle? - Answer 15 A A single receptacle connected to a 30-ampere branch circuit must generally have a rating not less than ------ amperes. - Answer 30 Amps If 15- and 20- ampere duplex receptacles are not marked with "CO/ALR" they are sui...

The term ampacity is defined as the ? current, in ampheres, that a conductor can carry continuously under conditions of use without exceeding its temperature rating. - Answer Maximum A conductor's ampacity is directly related to the type of insulation used on the conductor. - Answer True ...

Wire mesh grips provide ? and absorb ? . - Answer support / stress Strain relief grips differ from support grips in that they have ? attachments, which are easily attached to a junction box or panel. - Answer fitting Mechanically interlocked receptacles allow for the safe connection of p...

A multiwire branch circuit for an individual piece of utilization equipment supplies a line-to-neutral load. - Answer Acceptable 210.4(C) Exception No. 1 In general, the maximum voltage between conductors permitted to supply cord-and-plug-connected equipment other than luminaires in industr...

What is the minimum rating required for a receptacle? - Answer 15 A A single receptacle connected to a 30-ampere branch circuit must generally have a rating not less than ? amperes. - Answer 30 If 15- and 20-ampere duplex receptacles are not marked with "CO/ALR," they are suitable for ...