NCCCO Telescopic Boom Crane- Swing Cab(TLL) EXAM PREPARATIONs COMPILATION BUNDLE 100% GUARANTEED SUCCESS

DOMAIN 1: SITE IF OUTRIGGERS AREN'T QUITE FULLY EXTENDED, WHICH LOAD CAPACITY CHART SHOULD YOU REFER TO BEFORE LIFTING OPERATIONS? ON RUBBER CHART UNDER WHAT CIRCUMSTANCE(S) IS IT OKAY TO BLOCK UNDER THE OUTRIGGER BEAMS? IT IS NEVER ACCEPTABLE ANY TYPE OF IMPROPER BLOCKING OR CRIBBING SUCH AS ...

Load chart capacities distinguished in bald type, marked with an asterisk, in a shaded area, or above a bold line of the capacity chart are based on: (a) net capacity (b) dynamic loads (c) structural strength (d) tipping - (c) structural strength The proper way to calibrate a boom angle indicat...

Signal Person Qualifications (OSHA) 1926.1428 Hoisting Personnel (OSHA) 1926.1431 Authority to Stop (OSHA) 1926.1418 Powerline Safety (OSHA) 1926.1407 thru 1926.1411 Scope (OSHA) 1926.1400 Inspections (OSHA) 1926.1412 Tower Cranes (OSHA) 1926.1435 Wire Rope Inspections (OSHA) 1926.141...

Rotation-resistant rope may be used with a swivel - If the rope manufactory approves Working radius is defined as the distance from the - Center of rotation of the crane to the center of gravity of the load At what percentage of tipping are truck-mounted cranes on outriggers, which are fully exten...

T or F As crane signaling is only a basic function and the signal person knows where the loads will be positioned, training or testing of the signal person should not be required - False When using hand signals to direct a crane operator, an extended arm with the thumb vertical and the fingers ope...

When working on rubber, cranes are rated at what percentage of tipping: a) 70% b) 75% c) 80% d) 85% - 75% When a crane is working "on outriggers" the only time they should be less than fully extended is when: a) working alongside the highway and cannot block a lane b) you are handling light...

What is prohibited by OSHA 1926 Subpart cc regarding wire rope on a crane? - Splicing What should be of major concern when considering surfaces for crane set up locations? - Voids, tanks, loose fill, depressions Which items are included in the suspended weight when calculating parts of line? - Loa...

To provide protection in the cranes work area, barriers MUST be erected in accessible areas; - Within the equipment's rotating structure All of the following can cause a two-block condition except: - Raising the boom When rotation of load may be hazardous, the operator must - Ensure tag line is u...

Who can recreate or replace load charts for cranes? Only the crane manufacturer What is the gross load? The total weight of everything below the boom tip. What is the Net load? The gross load minus all applicable deductions. Do all cranes have both structural and stability based load charts? ...

The safety design factor for a personal platform structure and the rigging must be how many times it's intended capacity? - 5 According to OSHA, the assembly/disassembly director must be... - A competent and qualified person What is most important when performing a two crane pick? - Both cranes m...

Crane configuration includes: - Reeving, boom length, counterweight, on outriggers, on rubber, extensions or jibs stowed or mounted, offsets, wire rope type or construction How does the operator determine the manufacturers recommended rope for the crane? - Read the manufacturer load chart or operat...

Crane configuration includes - Reeving, boom length, counterweight, on outriggers, on rubbers, extensions or jibs stowed or mounted, off sets, wire rope type or construction. How does the operator determine the manufacturers recommended rope for the crane - Read the manufacturer load chart or opera...

Boom trucks normally do not have capacities in which operating area? - over the front What action can cause the lattice boom to topple backwards - swinging from the downhill side to the uphill side (When out of level) order of hitch strength, which is the correct answer - Basket, vertical, choker ...

On a lattice boom crawler crane, the main boom length is measured from the: - Center of the boom heel pins to the center of the boom tip sheave What is the main purpose of mid point suspension pendants? - To absorb shock that comes with dynamic loading The main purpose of a gantry or a mast on a c...