Summary Advanced Food Chemistry - Phenolics part
FCH-30806 at Wageningen University
This summary contains the following:
- Structure and biosynthesis of phenolics
- Analysis and isolation of phenolics
- Oxidation of phenolics
- Effect of structure on reactivity of phenolics
- Inhibition of ...
Summary Advanced Food Chemistry – Phenolics
Structure & biosynthesis
• Phenolics are in fruits, vegetables and nuts.
• Phenolics are present in low concentrations but reactive so large effect on quality!
• Organic compounds containing an aromatic hydrocarbon ring with at least 1 OH group.
1 OH = monophenol, 2 OH = diphenol, >3 OH = polyphenol
• Synthesized from the activated building blocks (precursors) p-coumaryl-CoA and malonyl-
CoA → ratio depends subclass of phenol
• OH group can be methylated → strictly no phenolic anymore
• Phenols can form oligomeric structures by
o Covalent linkages: carbon-carbon, ether (C-O), ester bonds or amide bonds
o Con-covalently linkages: stacking, metal chelation by OH groups, hydrophobic
interactions, H-bonds
Hydroxycinnamic acid (1 ring)
• Building block of a lot of compounds
• Contains a COOH group so it can form an ester with alcohol. For instance ester of caffeic acid
with quinic acid → chlorogenic acid
• They can form phenol-amides (contain an NH2 group)
Analysis & isolation
Step 1: extraction
• Defatting with hexane before extraction → higher recovery of phenolics & cleaner extract
• Select a suitable extraction solvent (organic solvent) → comparable polarity with phenols and
low boiling point (easy solvent evaporation after extraction). For instance methanol. Mixing of
extraction solvents is possible
• Re-extract the residual material of the extraction → continue until absorbance of last extract
is less than 5% of the sum of the absorbances of all previous extracts. Measure this with UV-
Vis at 280nm. Proteins are also show absorbance at this wavelength so you might overestimate
the amount of phenolics that is still in the residue. Too low wavelength: too much interference
because a lot of compounds show absorbance. Too high wavelength: not all compounds show
absorbance, too specific.
• Ratio between solvent and dry matter: important for extraction efficiency. With a little
solvent, you have to do more cycles
Step 2: sample clean up (removal of impurities)
• Solid-phase extraction (SPE):
o Apolar, carbon based (C18) stationary phase is used so the apolar phenolics bind to
this. Polar mobile phase elutes oligosaccharide contaminants. Mobile phase is polar so
reversed-phase SPE.
o After removal of oligosaccharides, the bound phenolics can be eluted by an apolar
mobile phase. First less apolar molecules elute. Most apolar molecules elute latest.
• Liquid-liquid extraction (LLE) / partitioning:
o Vigorous mixing → impurities and phenolics have the opportunity to distribute
themselves over two phases. Larger solubility difference = easier separation
o For instance carbohydrates in water phase and phenolics in ethyl acetate phase.
o You can also use this method (1) to defat the extract. Or (2) to remove e.g. sugars
, o Or (3) to transfer your compounds to organic solvent → easier to remove than by
freeze drying to remove water
• In both methods, pH of the extraction solvent is important because it depends the charge of
the phenolics! High pH = COO- instead of COOH → COO- makes the phenolic polar…
• Removal of the organic solvent after SPE or LLE:
o Longer stability of phenolics at lower water content & easier quantification
o Remove organic solvents by rotating evaporator. After that, dissolve them in water
and freeze dry them. Direct freeze-drying is not possible because their boiling point is
too low and this would lead to loosing phenolic material.
o Disadvantage: phenolics are not well water-soluble after freeze drying → compact,
inhomogeneous material is obtained after freeze drying
o Solution: use tert-butanol (organic solvent that is solid at room temperature) → does
not boil during freeze drying and phenolics are well soluble in tert-butanol
Step 3: analyses
Simple analyses
• UV-Vis: phenolics absorb light between 260 and 280nm because of their aromatic ring + OH
o Disadvantage: also proteins show absorbance so not accurate in mixtures
• Folin-Ciocalteu (total phenolics assay)
o Reaction between reducing substance and reagent → blue complexes
o Disadvantage 1: overestimation because also other reducing compounds
o Disadvantage 2: gallic acid is used as standard but there may be other phenolics that
have a higher response factor (more blue colour) but are not more present
• DPPH assay (antioxidant activity)
Advanced analytical methods
• Reversed phase LC coupled to PDA (UV-Vis detection) and MS (separation based on mass)
o Separation and detection of single compounds by UV-Vis and MS
o Advantages:
▪ You can use it for complex mixtures because also separation on mass by MS
▪ More sensitive than NMR (= can measure lower concentrations)
o Disadvantages:
▪ More laborious than upper methods (but more accurate)
▪ For best result you need calibration curve (standard compounds) for each
phenolic compound. When not available: (1) use molar extinction coefficient (=
how much light absorbs it compared to the compound you DO have a standard
from) or (2) express the quantity as equivalent of another structurally related
compound
• NMR spectroscopy
o Advantages: standard way, can be used for a lot of structures
o Disadvantages: difficult to apply in mixtures, difficult to interpretate
o 1 dimensional: 1H and 13C NMR → analyse the protons and carbon atoms in your
structure
o 2 dimensional: correlations between different atoms in the structure. COSY:
correlations between protons and other protons in the structure.
o Peak area can be used to see how much of the atom is present.
Why to isolate pure phenolic compounds?
• To elucidate structures of new compounds by NMR
• To determine its chemical properties (e.g. molar extinction coefficient)
• To asses the bioactivity and perform QSAR studies
• To use the pure compound as standard for future quantification
How to isolate pure phenolic compounds from a plant extract?
• Extract of the plant extract (defatting and extraction with methanol)
• Sample clean up (SPE or LLE)
• Pre-purification (for instance by flash chromatography) → fractions high in a certain compound
• Purification by preparative LC
➔ It takes weeks to do this and you have low yields!
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller bsc_msc_food_technology. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $3.18. You're not tied to anything after your purchase.
