NCCER MILLWRIGHT PRACTICE EXAM 2 LATEST 2023 WITH COMPLETE SOLUTION
1 view 0 purchase
Course
Millwright
Institution
Millwright
NCCER MILLWRIGHT PRACTICE EXAM 2 LATEST 2023 WITH COMPLETE SOLUTION
unusual
If the seal was not properly aligned or there is excessive wear in some bearing or shaft,_______ wear tracks will be the indicator
sharpened brass putty knife
For removing hard to remove gasket materials found on seal...
NCCER MILLWRIGHT PRACTICE EXAM 2 LATEST
2023 WITH COMPLETE SOLUTION
unusual
If the seal was not properly aligned or there is excessive wear in some bearing or
shaft,_______ wear tracks will be the indicator
sharpened brass putty knife
For removing hard to remove gasket materials found on sealing surfaces, ______ is
recommended
Conducted on the job
Apprenticeship training is_______
distance
Charting alignment on a graph requires a chart that is divided into thousandths of an
inch vertically for the indicator readings and into whole inches horizontally for
the__________
hidden
The orthographic drawing may contain a dashed or _______ line
Radiation
In order to shoot through a test object and project an image onto a detector or a sheet
of film, radiography uses a source of penetrating called _______
*scribe circles
*transfer measurements
*compare distances
<measure angles
Which of the following task would you not perform with dividers?
10%
The over speed trip device is actuated when the turbine reaches a predetermined limit
usually _________% above normal full-load speed
high
Positive results in an offset measurement mean that the MTBM is _____ or on the 3-
o'clock side.
offset misalignment
The coupling gap is set, and then the ______ is measured
pressure
In a hydraulic system, movement depends on_____
furniture or utility items
Fractional dimensions are used on objects such as _______ or ______
elimination
If the cause of the problem is not immediately understood, the process of________is
often the procedure of choice
3/16
When applying sealant to the sealing gland flanges, keep the sealant away from the
inside edges of the flange by at least_______ inch
Transducer
A stroboscope is triggered by a_______
, thread
The pitch of threaded fasteners is measured with a ________gauge
Surface cracks
Liquid penetrant highlights flaws and reveals________
die
A tool used to cut external threats on s bolt or rod is called a ______
special processes
A bill of materials may include info on _______ and other reference information
surface speed
Engaged gears always have the same _____
general arrangement
Elevation of equipment is usually found in the_____
Vibrations
Inspect the pulleys, rollers, and idlers for unevenness or______
15-20 degree angle
When cutting thin steel with Oxyfuel fuel cutting equipment, hold the torch so that the tip
is pointing in the direction the torch is traveling at a _____ angle
Grease.........
Labby seals work BEST with materials such as_____
Friction
Lubrication is the application of any substance that reduces________
Driver coupling jig
When the dial indicator is mounted on the complex reverse driven coupling jig , the
indicator is registered on the____
In racks
Pipe should be stored_____
Single deep groove radial
The most common type of ball bearing is a _____ bearing
split
Couplings that are installed after the driver and driven shafts have been aligned and the
equipment has been fastened into position are ________ couplings
Factors
When two or more numbers are multiplied to make another number thy ate called
_______of the third number
clockwise
The continuous-reading dial indicator starts at zero and increases _________
Electronic filters
Vibration within a specific narrow band range can be detected by _______
Teflon
What type of o ring do you use with temperatures between-300 and 500?
Rivet cutting
The special cutting til for cutting off bolt heads and nuts is called a ______ tip
pressure
PCVs limit and regulate _______in the system
Displacement
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller magdamwikash23. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $11.49. You're not tied to anything after your purchase.
