NEIEP 700 Final Exam V1 (New 2023/ 2024
Update) Questions and Verified Answers| 100%
Correct| Graded A
1)The first type of elevator was powered by pulling an endless looped
rope called bull rope to raise and lower you and the platform -
ANSWER--1)True
2)Floor stop accuracy or early alternating current motor elevators was a
vast improvement over direct current motor elevators - ANSWER--
2)False
3)Today all elevators operating in the US must operate according to the
American society of mechanical engineers code - ANSWER--3)True
What use lines and symbols to show the arrangement of electrical
circuits, components and connections for a job. - ANSWER--Straight line
wiring diagram
The correct name for a multimeter is a VOM multimeter , which stands
for - ANSWER--Volt , ohms, and miliamphere
What are designed to store and discharge electrical energy . If not
discharged they are able to retain this electrical energy for long periods
of time . - ANSWER--Capacitor
, NEIEP 700 Final Exam V1 (New 2023/ 2024
Update) Questions and Verified Answers| 100%
Correct| Graded A
A safe way to discharge or bleed the electrical energy from a 125 - volt
capacitor is to use? - ANSWER--10k ohm resistor
8) Digital and analog meters are very durable instruments and can
tolerate rough handling . - ANSWER--8)False
9)Elevator constructors should start the elevator troubleshooting
process simple, check the easy things first. - ANSWER--9) True
What Control system , and elevator traveling up will not change
directions until the highest of the registered calls are answered. -
ANSWER--Selective collective control
The rubbing or sliding motion as relay contacts touch is called
____________________. This is an important function because it keeps
the contact surfaces clean and conducting properly. - ANSWER--Contact
wipe
12)When an elevator constructor describes a normal open contact or a
making contact he or she is describing the same contact configuration. -
ANSWER--12)true
, NEIEP 700 Final Exam V1 (New 2023/ 2024
Update) Questions and Verified Answers| 100%
Correct| Graded A
13. As current flows through a relay's coil _______________________
generated by the coil will pull or pick the relay's armature . - ANSWER--
Magnetic field
14)The most common relay used today is the plug type. - ANSWER--14)
True
15. The majority of today's set / reset work by using two independent
coils mounted to a common relay base . - ANSWER--15) True
16. What prevents two or more relays from becoming energized or
picked electrically at the same time . - ANSWER--Electrical interlock
17. What allows current to flow in only one direction . - ANSWER--
Diode
18. In a DC circuit , diodes that have a negative voltage on the bar side
of the diode will make this diode what? - ANSWER--Forward Bias
19. Dashpots are timers that use oil flow to control their tripping time .
- ANSWER--19. True
Update) Questions and Verified Answers| 100%
Correct| Graded A
1)The first type of elevator was powered by pulling an endless looped
rope called bull rope to raise and lower you and the platform -
ANSWER--1)True
2)Floor stop accuracy or early alternating current motor elevators was a
vast improvement over direct current motor elevators - ANSWER--
2)False
3)Today all elevators operating in the US must operate according to the
American society of mechanical engineers code - ANSWER--3)True
What use lines and symbols to show the arrangement of electrical
circuits, components and connections for a job. - ANSWER--Straight line
wiring diagram
The correct name for a multimeter is a VOM multimeter , which stands
for - ANSWER--Volt , ohms, and miliamphere
What are designed to store and discharge electrical energy . If not
discharged they are able to retain this electrical energy for long periods
of time . - ANSWER--Capacitor
, NEIEP 700 Final Exam V1 (New 2023/ 2024
Update) Questions and Verified Answers| 100%
Correct| Graded A
A safe way to discharge or bleed the electrical energy from a 125 - volt
capacitor is to use? - ANSWER--10k ohm resistor
8) Digital and analog meters are very durable instruments and can
tolerate rough handling . - ANSWER--8)False
9)Elevator constructors should start the elevator troubleshooting
process simple, check the easy things first. - ANSWER--9) True
What Control system , and elevator traveling up will not change
directions until the highest of the registered calls are answered. -
ANSWER--Selective collective control
The rubbing or sliding motion as relay contacts touch is called
____________________. This is an important function because it keeps
the contact surfaces clean and conducting properly. - ANSWER--Contact
wipe
12)When an elevator constructor describes a normal open contact or a
making contact he or she is describing the same contact configuration. -
ANSWER--12)true
, NEIEP 700 Final Exam V1 (New 2023/ 2024
Update) Questions and Verified Answers| 100%
Correct| Graded A
13. As current flows through a relay's coil _______________________
generated by the coil will pull or pick the relay's armature . - ANSWER--
Magnetic field
14)The most common relay used today is the plug type. - ANSWER--14)
True
15. The majority of today's set / reset work by using two independent
coils mounted to a common relay base . - ANSWER--15) True
16. What prevents two or more relays from becoming energized or
picked electrically at the same time . - ANSWER--Electrical interlock
17. What allows current to flow in only one direction . - ANSWER--
Diode
18. In a DC circuit , diodes that have a negative voltage on the bar side
of the diode will make this diode what? - ANSWER--Forward Bias
19. Dashpots are timers that use oil flow to control their tripping time .
- ANSWER--19. True
