ASE Brakes A5 Test ( Exam 1 ), ASE A5 Brakes, ASE Brakes A5 ( Exam 3 ), ASE Brakes A5 Test ( Exam 2 ) answered
2 views 0 purchase
Course
ASE Brakes A5
Institution
ASE Brakes A5
ASE Brakes A5 Test ( Exam 1 ), ASE A5 Brakes, ASE Brakes A5 ( Exam 3 ), ASE Brakes A5 Test ( Exam 2 ) answered
A drum is chattering on the brake lathe. This could be a result of
a. failure to install the dampening belt
b. cutting too slowly
c. dull cutting blades
d. cutting speed too ...
ASE Brakes A5 Test ( Exam 1 ), ASE A5
Brakes, ASE Brakes A5 ( Exam 3 ), ASE
Brakes A5 Test ( Exam 2 ) answered
A drum is chattering on the brake lathe. This could be a result of
a. failure to install the dampening belt
b. cutting too slowly
c. dull cutting blades
d. cutting speed too fast
A : failure to install the dampening belt
why : a missing dampening belt could cause the drum to vibrate while on the lathe. this vibration can
cause the drum to bounce on the cutting tip and make a chattering noise
A vehicle equipped with a hydro-boost brake system has a hard pedal with little braking action. Which
of the following could be the cause?
a. low brake fluid
b. air in the brake fluid
c. low power steering fluid
d. an overtightened power steering belt
C : low power steering fluid
why : low power steering fluid can cause the booster to provide very little if any boost
Which of the following could cause excessive noise braking?
a. worn wheel cylinders
b. worn caliper pistons
c. seized caliper slides
d. missing clips
D : missing clips
why : missing anti-rattle clips could cause excessive noise while braking
,A vehicle equipped with a "hill holding" option has an ABS code. Which tool would most likely be used
to check the wheel speed sensor?
a. AC volt meter
b. Ohm meter
c. Scan tool
d. Ammeter
C : scan tool
why : a scan tool or oscilloscope can be used to test a signal from a digital when speed sensor
The brake system has a soft, sinking pedal with the engine running. The brake fluid level is at the
correct height. Which of the following could be the cause?
a. a restricted vacuum hose
b. a leaking master cylinder
c. a bypassing master cylinder
d. a stuck open vacuum check valve
C : a bypassing master cylinder
why : a bypassing master cylinder would cause a low pedal and would not cause a loss of fluid
Technician A says the pins should be driven in with a brass hammer. Technician B says the pins should
be lubricated with brake fluid. Who is correct? ( pg. 47 )
a. A
b. B
c. A & B
d. neither A OR B
D : neither A OR B
why : neither technician is correct. this style of pin should be installed with a torx or hex head socket
Technician A says a hydro-boost system can use the power steering pump to operate the booster.
Technician B says a hydro-boost system can use engine vacuum to operate the booster. Who is
correct? ( pg. 47 )
a. A
b. B
c. A & B
d. neither A & B
,A : only A
why : only tech A is correct. a hydro-boost system uses hydraulic pressure to create boost
A disc brake caliper is dragging. All of the following could be the cause EXCEPT
a. binding pins
b. sticking piston
c. binding caliper
d. worn brake pads
D : worn brake pads
why : worn brake pads will not cause the brakes to drag
Which operation is being performed in the illustration? ( pg. 48 )
a. wheel cylinder bleeding
b. brake caliper bleeding
c. master cylinder bleeding
d. master cylinder pressure test
C : master cylinder bleeding
why : the master cylinder is being bleed prior to installation
The rear wheels of a front wheel drive car lockup during heavy breaking. Technician A says this could
be cause by faulty proportioning valve. Technician B says this could be caused by a faulty brake
booster. Who is correct?
a. A only
b. B only
c. Both A & B
d. Neither A or B
A : A only
why : tech A is correct. a faulty proportioning valve could cause the pressure to the rear wheels to be
too high and lock the wheels during hard braking
There is a loud growling noise only when the vehicle is steered to the right while driving. Which of the
following could be the cause?
a. work left front brakes
b. worn wheel bearing
c. worn right front brakes
d. sticking brake caliper
, B : worn wheel bearing
why : this is a typical wheel bearing noise
A spongy pedal can be the result of:
a. leaking wheel cylinders
b. broken return springs
c. contaminated linings
d. seized wheel cylinder pistons
A : leaking wheel cylinders
why : a spongy pedal can result from air in the hydraulic system. leaking wheel cylinders could allow air
to get into the hydraulic system and result in a spongy pedal
A vehicle has a wheel speed sensor diagnostic trouble code. Which of the following is the LEAST LIKELY
cause?
a. faulty wheel speed sensor
b. cracked wheel speed sensor reluctor ring
c. a tire with the incorrect height
d. a tire with the incorrect width
D : a tire with the incorrect width
why : the width of the tire will not affect the wheel speed sensor signal
A vehicle has a squeak only when applying the breaks. Which of the following could be the cause?
a. aerated brake fluid
b. water contaminated break fluid
c. worn brake pads
d. worn wheel bearings
C : worn brake pads
why : worn pads can cause a squeak when applying the brakes
During a moderate brake pedal application, with the engine running, what would be considered a
normal pressure reading on the inlet pressure gauge? ( pg. 49 )
a. 100 psi
b. 900 psi
c. 3,000 psi
d. 5,000 psi
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller MUTUKACOURSEHERO. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $7.99. You're not tied to anything after your purchase.
