100% satisfaction guarantee Immediately available after payment Both online and in PDF No strings attached
logo-home
Previously searched by you
Previously searched by you
logo
ELEN7018: Earthing and Lightning Project Project - High Level Design of Earthing and Lightning Protection System for an Upgrade of a site to Wind and Solar Generation Plant in the Eastern Cape $30.83
Add to cart
Quickly navigate to
Preview
  2.  
  3. University Of The Witwatersrand (wits)
  4.  
  5. Electrical Engineering

Thesis

ELEN7018: Earthing and Lightning Project Project - High Level Design of Earthing and Lightning Protection System for an Upgrade of a site to Wind and Solar Generation Plant in the Eastern Cape

1 review
 6 purchases
  • Course
  • Electrical Engineering
  • Institution
  • University Of The Witwatersrand (wits)
  • Book
  • Understanding Lightning and Lightning Protection

This report detail a high level design undertaken for a mix of renewable resources site of an assumed area of 750km2 in the Eastern Cape with a ground flash density of 10 flashes/ km2/year in a sandy and loose soil with average resistivity of 1225Ωm which was found to cause mild corrosion effect ...

[Show more]

Preview 4 out of 65  pages

Document information

  • January 27, 2019
  • 65
  • 2017/2018
  • Thesis
  • Unknown
  • Unknown

Subjects

  • risk assessment
  • surge protective device
  • physical damage
  • earth termination
  • air terminal
  • bond conductor
  • down conductor

Connected book

book image

Book Title:

Author(s):

  • Edition:
  • ISBN:
  • Edition:

Written for

  • University of the Witwatersrand (wits)
  • Electrical Engineering
All documents for this subject (7)

1  review

review-writer-avatar

By: elethugibeni • 4 year ago

Seller

avatar-seller
Mpincham

Reviews received

Content preview

ELEN7018: EARTHING AND LIGHTNING PROTECTION

Course Project: High Level Design of Earthing and Lightning Protection System for an
Upgrade of a site to Wind and Solar Generation Plant in the Eastern Cape.




Candidate
Student Name

Student Number
XXXXXX

I hereby declare this is my own unaided work, submitted in partial fulfillment for the degree
in Master of Engineering in Electrical

,ELEN7018 Project: High Level Design of Earthing and Lightning Protection System for an Upgrade of
a Site to Wind and Solar Generation Plant in the Eastern Cape

Table of Contents


1
Abstract ......................................................................................................................................... 7
1. INTRODUCTION .................................................................................................................... 8
2. CLASSIFICATION OF STRUCTURE TO BE PROTECTED ................................................... 8
2.1 Sizing of renewable energy ................................................................................................. 9
2.1.1 Wind turbine ................................................................................................................. 9
2.1.2 Photovoltaic ................................................................................................................. 9
2.1.3 Plant layout assumptions ........................................................................................... 10
3. RISK ASSESSMENT AND DETERMINATION OF PROTECTION LEVEL ........................... 11
4. EXTERNAL LIGHTNING PROTECTION SYSTEM (LPS) ..................................................... 14
4.1 Selection of material type for external LPS ........................................................................ 14
4.1.1 Soil resistivity assessment ......................................................................................... 14
4.1.2 Corrosion effect.......................................................................................................... 14
4.1.3 Material dimensions and area of application .............................................................. 15
4.2 Air termination ................................................................................................................... 15
4.2.1 The rolling Sphere method ......................................................................................... 15
4.2.2 The angle protective method ...................................................................................... 16
4.2.3 Mesh size method. ..................................................................................................... 17
4.3 Down conductor system .................................................................................................... 18
4.4 Earth termination system .................................................................................................. 18
4.4.1 Earth electrode arrangement...................................................................................... 18
4.4.2 Foundation of earth electrodes................................................................................... 20
5. INTERNAL LIGHTNING PROTECTION SYSTEM (LPS) ...................................................... 21
5.1 Equipotential bonding for metal installations ..................................................................... 21
5.2 Selection of surge protection devices (SPDs).................................................................... 22
5.2.1 Lightning protection zone (LPZ) boundaries ............................................................... 22
5.2.2 Wind turbines SPDs ................................................................................................... 23
5.2.3 PV arrays and solar generation buildings SPDs ......................................................... 24
5.2.4 Operations and control room SPDs ............................................................................ 25
6. MAINTENANCE ................................................................................................................... 26
7. SOCIOCULTURAL ASPECTS.............................................................................................. 27
8. CONCLUSION...................................................................................................................... 28
Reference .................................................................................................................................... 29
Appendix A: Solar Photovoltaic System Sizing ............................................................................ 30
Appendix B: Risk Assessment Calculations ................................................................................. 32

Page |2
XXXXXX

,ELEN7018 Project: High Level Design of Earthing and Lightning Protection System for an Upgrade of
a Site to Wind and Solar Generation Plant in the Eastern Cape

Appendix C: Cables protection measures .................................................................................... 46
Appendix D: Tasks ...................................................................................................................... 50




Page |3
XXXXXX

, ELEN7018 Project: High Level Design of Earthing and Lightning Protection System for an Upgrade of
a Site to Wind and Solar Generation Plant in the Eastern Cape

List of Figures
Figure 1: Upgraded Site to Wind and Solar Generation ..................................................................... 8
Figure 2: Wind turbine dimensions [2] ............................................................................................... 9
Figure 3: Solar photovoltaic system, side and front view. ................................................................ 10
Figure 4: Wind turbines and PV system reticulation ........................................................................ 10
Figure 5: Schematic application of the rolling sphere method for wind turbine and PV arrays ......... 16
Figure 6: Protective angle as function of h based on the class of LPL ............................................. 16
Figure 7: Protective angle method applied to PV arrays .................................................................. 17
Figure 8: Building structure protected by mesh size method ........................................................... 17
Figure 9: Type B earth electrode arrangement of the renewable sources site ................................. 19
Figure 10: Minimum length I1 of each earth electrode according to the class of LPS [7] .................. 19
Figure 11: Bonding of services at the boundary [9].......................................................................... 21
Figure 12: Division of wind turbine into different lightning protection zones ..................................... 22
Figure 13: Example - SPDs installed at the zone boundaries of a wind turbine [10] ........................ 23
Figure 14: Example - Lightning protection concept for a PV power plant with central inverter [10] .. 25
Figure 15: Example - SPDs coordination for power and signal cables in the control cable .............. 26

List of Tables
Table 1: Buildings (MCR, CR1, CR2): Risk R1 for the unprotected structure (value 1x10 − 5) ......... 12
Table 2: Buildings (SG1, SG2, SG3) and PV Arrays (PV1, PV2, PV3): Risk R2 for the unprotected
structure (value 1x10 − 3)................................................................................................................ 12
Table 3: a) Buildings (MCR, CR1, CR2): Risk R1 with SPDs of LPL IV ............................................ 13
Table 4: b) Buildings (MCR, CR1, CR2): Risk R1 with SPDs of LPL IV ............................................ 13
Table 5: Relationship between soil resistivity and corrosiveness ..................................................... 14
Table 6: Material dimensions [7]...................................................................................................... 15
Table 7: Material and area of applicability [7] .................................................................................. 15
Table 8: Protection levels for down conductors ............................................................................... 18
Table 9: Structures lightning protection zone (LPZ) boundaries ...................................................... 22




Page |4
XXXXXX

The benefits of buying summaries with Stuvia:

Guaranteed quality through customer reviews

Guaranteed quality through customer reviews

Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.

Quick and easy check-out

Quick and easy check-out

You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.

Focus on what matters

Focus on what matters

Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!

Frequently asked questions

What do I get when I buy this document?

You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.

Satisfaction guarantee: how does it work?

Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.

Who am I buying these notes from?

Stuvia is a marketplace, so you are not buying this document from us, but from seller Mpincham. Stuvia facilitates payment to the seller.

Will I be stuck with a subscription?

No, you only buy these notes for $30.83. You're not tied to anything after your purchase.

Can Stuvia be trusted?

4.6 stars on Google & Trustpilot (+1000 reviews)

68175 documents were sold in the last 30 days

Founded in 2010, the go-to place to buy study notes for 15 years now

Start selling
$30.83  6x  sold
  • (1)
Add to cart
Added