Exam (elaborations)
ASE MLR Certification Test
- Course
- Institution
ASE MLR Certification Test
[Show more]
Seller
Follow
lydiaomutho
Content preview
ASE MLR Certification Test0.368 Volts - ANS-A digital multimeter (DMM) set on the mV scale has a display reading
of 368. Which of these values does the reading represent?
0.450 volts - ANS-A digital multimeter (DMM) reading of 450 mV is equal to:
0.728 - ANS-On a Metric Micrometer upper sleeve reading 5.0mm with lower sleeve
reading 0.50mm and a thimble reading of 0.01mm what is the overall reading?
300 amps for 15 seconds - ANS-A fully charged battery rated at 600 CCA, the ambient
temperature is 70 degrees which of these current and time periods should be used?
A CVT can change steplessly through an infinite number of effective gear ratios
between maximum and minimum values - ANS-Which of these best describes the
operation of a continuously variable transmission (CVT)?
A loose accessory drive belt - ANS-A vehicle has a squealing noise that changes with
engine speed. This could be caused by:
A only - ANS-A driveshaft universal joint is being replaced and the technician cannot
install the retaining clip. Technician A says that a dislocated needle bearing could be the
cause. Technician B says that a damaged spline in the yoke could be the cause. Who is
right?
A only - ANS-A floating front brake caliper is being replaced. Technician A says that
after installation, the brake hose to caliper fitting should be checked for leaks.
Technician B says that both caliper pins should be lubricated with DOT 4 brake fluid.
Who is right?
A only - ANS-A vehicle is being checked for power steering fluid leaks. Technician A
says that leaks can develop in the fittings, hoses, and seals. Technician B says that the
steering components should be observed for leaks while a helper turns the steering
wheel to the right and left. Who is right?
A only - ANS-Both front wheels are to be removed from a vehicle. Technician A says
that if a floor jack is to be used to raise the vehicles, the vehicle should be supported
with jack stands. Technician B says that if an electric lift is to be used to raise the
vehicle, jack stands should be placed at the four corners of the vehicle. Who is right?
, A only - ANS-During an instruction panel gauge test, the technician observes that the
engine temperature gauge is reading 200 F (93 C) on a cold engine. Technician A says
that a scan tool can be used to compare the gauge reading to the coolant temperature
sensor reading. Technician B says that an open coolant thermostat could be the cause.
Who is right?
A only - ANS-Technician A says that a positive crankcase ventilation (PCV) system
reduces vehicle emissions. Technician B says that a positive crankcase ventilation
(PCV) system helps increase crankcase pressure. Who is right?
A only - ANS-Technician A says that disconnecting the negative battery cable may be
required to disable the air bag system. Technician B says that a self-powered test light
can be used to test air bag system components. Who is right?
A only - ANS-Technician A says that disconnecting the negative battery cable may be
required to disable the airbag system. Technician B says that a self-powered test light
can be used to test air bag system components. Who is right?
A only - ANS-Technician A says that excessive play of the inner tie rod indicates that the
inner tie rod must be replaced. Technician B says that a torn bellows boot on the rack
and pinion indicates that the outer tie rod end must be replaced. Who is right?
A only - ANS-Technician A says that eye protection should be worn at all times while in
the laboratory area. Technician B says that regular prescription eyewear may be worn
as a substitute for safety glasses. Who is right?
A only - ANS-Technician A says that rosin-core solder should be used when soldering
electrical connections. Technician B says that a crimp and shrink connector can be used
when repairing electrical wiring. Who is right?
A only - ANS-Technician A says that tire rotation helps to extend tire lief. Technician B
says that directional tires should be rotated in an "X" pattern. Who is right?
A only - ANS-Technician A says that, when reinstalling a wheel and tire assembly on a
vehicle, the lug nuts should be tightened using a torque wrench. Technician B says that,
when reinstalling a wheel and tire assembly on a vehicle, the lug nut should be
tightened in a circular pattern. Who is right?
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller lydiaomutho. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $7.99. You're not tied to anything after your purchase.
Can Stuvia be trusted?
4.6 stars on Google & Trustpilot (+1000 reviews)
81531 documents were sold in the last 30 days
Founded in 2010, the go-to place to buy study notes for 14 years now