Exam (elaborations)
NACE CIP 1 CBT EXAM PRACTICE QUESTIONS & ANSWERS.
- Course
- Institution
NACE CIP 1 CBT EXAM PRACTICE QUESTIONS & ANSWERS.
[Show more]
Seller
Follow
Wisdoms
Reviews received
Content preview
NACE CIP 1 CBT EXAM PRACTICEQUESTIONS & ANSWERS
Dew point is the temperature at which - Correct Answer - condensation occurs.
You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank lining is being
applied. After application of the 19 coat you notice small blisters in some areas of the applied lining.
Your FIRST preferred course of action is to: - Correct Answer - Document the problem and advise the
Contractor and Owner's representative.
If a contractor is using a poorly maintained compressor to supply air for abrasive blast cleaning and
conventional airspray, the coating inspector should perform a - Correct Answer - blotter test for the
presence of oil and water.
Upon arrival of coating materials, the inspector should - Correct Answer - observe and document the
amount of material and batch numbers.
Relative humidity is - Correct Answer - a measure of the amount of moisture in the air compared to
saturation level.
Galvanic corrosion occurs on which of the following substrates? - Correct Answer - Metal
When applying Thermal Spray Coatings the specification is most likely to reference: - Correct Answer -
SSPC-CS 23.00/AWS C2.23/NACE No. 12
What is the minimum recommended distance away from an edge that an inspector should take a
measurement with a dial type magnetic pull off Dry Film Thickness(DFT) gauge? - Correct Answer - 2.5
cm (1 inch)
Polymerization is the process of? - Correct Answer - Monomers joining together.
An exposed area of the substrate or previous coat of a conductive material, often caused by poor
application technique is called: - Correct Answer - Holiday
Checking is: - Correct Answer - a fine crack in the surface of a coating that rarely reaches the substrate.
Inspection documentation is important because: - Correct Answer - Owners use the documentation for
a variety of purposes.
, An Inspectors personal log book should contain: - Correct Answer - No comments regarding the
application team.
You have just received your NACE CIP Level 1 certification when you are asked to supervise a team of
uncertified field pipeline inspectors. Your FIRST preferred course of action is to: - Correct Answer -
Review the NACE Attestation prior to making a decision.
Good record can provide maintenance departments with detailed information about ALL of the
following EXCEPT: - Correct Answer - How the item was coated.
Non Conformance Reports are completed by the Inspector: - Correct Answer - When the Inspector and
Contractor deem it to be significant non conforming item.
The initial steel condition is important to the NACE Inspector because: - Correct Answer - The Inspector
may have to reject the steel.
The form of corrosion that has the largest potential for unexpected catastrophic failure is: - Correct
Answer - Galvanic Corrosion
What is used to determine compressed air cleanliness? - Correct Answer - Profilometer
Osmotic blistering is most likely to occur as a result of: - Correct Answer - Airless spray application.
When performing tests for oil and grease using an ultra violet light, the NACE Inspector should be aware
that: - Correct Answer - Synthetic oil or grease may not be identified.
To achieve consistently accurate results with ALL alt test equipment: - Correct Answer - wash your
hands before sampling.
When holiday testing is required the Inspector is always required to enforce what standard? - Correct
Answer - NACE SP 0188
If the specifier does not identify a restriction level in accordance with SSPC PA 2, the default restriction
level is: - Correct Answer - Level 3
Fine cracks in the surface of a coating that rarely reach the substrate are called: - Correct Answer -
Checking
It is good practice for the NACE Inspector to have instrument calibration certificates available: - Correct
Answer - At all times.
In a non convertible coating the role of the primary solvent is to: - Correct Answer - To control the
evaporation rate.
Removal of weld splatter is required: - Correct Answer - When specifically identified in the owners
specification.
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller Wisdoms. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $9.49. You're not tied to anything after your purchase.
Can Stuvia be trusted?
4.6 stars on Google & Trustpilot (+1000 reviews)
76799 documents were sold in the last 30 days
Founded in 2010, the go-to place to buy study notes for 14 years now