NCCER MILLWRIGHT PRACTICE EXAM 2 QUESTIONS AND ANSWERS
1 view 0 purchase
Course
NCCER
Institution
Amsterdam University College (AUC)
NCCER MILLWRIGHT PRACTICE EXAM
2 QUESTIONS AND ANSWERS
unusual - CORRECT ANSWER-If the seal was not properly aligned or there is
excessive wear in some bearing or shaft,_______ wear tracks will be the indicator
sharpened brass putty knife - CORRECT ANSWER-For removing hard to remove
gaske...
NCCER MILLWRIGHT PRACTICE EXAM
2 QUESTIONS AND ANSWERS
unusual - CORRECT ANSWER-If the seal was not properly aligned or there is
excessive wear in some bearing or shaft,_______ wear tracks will be the indicator
sharpened brass putty knife - CORRECT ANSWER-For removing hard to remove
gasket materials found on sealing surfaces, ______ is recommended
Conducted on the job - CORRECT ANSWER-Apprenticeship training is_______
distance - CORRECT ANSWER-Charting alignment on a graph requires a chart that is
divided into thousandths of an inch vertically for the indicator readings and into whole
inches horizontally for the__________
hidden - CORRECT ANSWER-The orthographic drawing may contain a dashed or
_______ line
Radiation - CORRECT ANSWER-In order to shoot through a test object and project an
image onto a detector or a sheet of film, radiography uses a source of penetrating called
_______
*scribe circles
*transfer measurements
*compare distances
<measure angles - CORRECT ANSWER-Which of the following task would you not
perform with dividers?
10% - CORRECT ANSWER-The over speed trip device is actuated when the turbine
reaches a predetermined limit usually _________% above normal full-load speed
high - CORRECT ANSWER-Positive results in an offset measurement mean that the
MTBM is _____ or on the 3-o'clock side.
offset misalignment - CORRECT ANSWER-The coupling gap is set, and then the
______ is measured
pressure - CORRECT ANSWER-In a hydraulic system, movement depends on_____
furniture or utility items - CORRECT ANSWER-Fractional dimensions are used on
objects such as _______ or ______
, elimination - CORRECT ANSWER-If the cause of the problem is not immediately
understood, the process of________is often the procedure of choice
3/16 - CORRECT ANSWER-When applying sealant to the sealing gland flanges, keep
the sealant away from the inside edges of the flange by at least_______ inch
Transducer - CORRECT ANSWER-A stroboscope is triggered by a_______
thread - CORRECT ANSWER-The pitch of threaded fasteners is measured with a
________gauge
Surface cracks - CORRECT ANSWER-Liquid penetrant highlights flaws and
reveals________
die - CORRECT ANSWER-A tool used to cut external threats on s bolt or rod is called a
______
special processes - CORRECT ANSWER-A bill of materials may include info on
_______ and other reference information
surface speed - CORRECT ANSWER-Engaged gears always have the same _____
general arrangement - CORRECT ANSWER-Elevation of equipment is usually found in
the_____
Vibrations - CORRECT ANSWER-Inspect the pulleys, rollers, and idlers for unevenness
or______
15-20 degree angle - CORRECT ANSWER-When cutting thin steel with Oxyfuel fuel
cutting equipment, hold the torch so that the tip is pointing in the direction the torch is
traveling at a _____ angle
Grease......... - CORRECT ANSWER-Labby seals work BEST with materials such
as_____
Friction - CORRECT ANSWER-Lubrication is the application of any substance that
reduces________
Driver coupling jig - CORRECT ANSWER-When the dial indicator is mounted on the
complex reverse driven coupling jig , the indicator is registered on the____
In racks - CORRECT ANSWER-Pipe should be stored_____
Single deep groove radial - CORRECT ANSWER-The most common type of ball
bearing is a _____ bearing
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller TIFFACADEMICS. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $15.49. You're not tied to anything after your purchase.
