Exam (elaborations)
IICL CHASSIS INSPECTOR COMPLETE EXAM 2024V
- Course
- Institution
IICL CHASSIS INSPECTOR COMPLETE EXAM 2024
[Show more]
Seller
Follow
michealmuthii
Reviews received
Content preview
IICL CHASSIS INSPECTOR COMPLETE EXAM 2024| ACTUAL EXAM QUESTIONS AND CORRECT ANSWERS| SCORED 100%What is traction control? - ANSWER Helps the ABS improve vehicle traction by minimizing wheel slip on the drive axle during acceleration.
What is ABS? - ANSWER Antilock braking systems are electronic systems that monitor and control wheel slip during vehicle braking.
What are the components of ABS? - ANSWER electronic control unit (ECU), wheel
speed sensors, modulator valves, exciter rings
In ABS, what is the function of the electronic control unit (ECU)? - ANSWER Processes all ABS info and signal functions. Receives and interprets voltage pulses generated by the sensor pickup as the exciter teeth pass by, and uses this info to determine: (a) impending wheel lock, and (b) when/how to activate the ABS modulator valves.
In ABS, what is the function of the modulator valves? - ANSWER Regulate air pressure to the brakes during ABS action. ECU commands mod valve to either change the air pressure to the brake chamber, or hold the existing pressure.
In ABS, what are the 2 main components of the wheel speed sensors ? - ANSWER (1) exciter, and (2) pickup
In ABS, what is an exciter? - ANSWER A ring with notched teeth, also known as sensor ring, tooth wheel, tone ring, and exciter.
In ABS, what is an pickup? - ANSWER Commonly called "the sensor" which contains a wire coil/magnet assembly, which generates pulses of electricity as teeth of the exciter pass in front of it.
Which pin/wire is the power supply for ground on a 7-way plug? - ANSWER Pin 1 -
white
Which pin/wire is the power supply for stop and antilock on a 7-way plug? - ANSWER Pin 2 - red
Which pin/wire is the power supply for power for electronic control unit (ECU) on a 7-
way plug? - ANSWER Pin 3 - blue
Which pin/wire is the power supply for identification, front and intermediate markers, front clearance, rear markers, license, tail and rear clearance on a 7-way plug? - ANSWER Pin 4 - brown Which pin/wire is the power supply for right directional on a 7-way plug? - ANSWER
Pin 5 - green
Which pin/wire is the power supply for left directional on a 7-way plug? - ANSWER Pin 6 - yellow
Which pin/wire is the power supply for ABS warning light on a 7-way plug ? - ANSWER Pin 7 - green/white
What is the transition area? - ANSWER Location where the gooseneck meets the main rails
What is a "horn" on a chassis? - ANSWER Large gathering structure extending above the top flange of the front of the chassis. It is a gathering device used to guide
containers lifted on/off chassis, and to restrict forward movement.
What is a kingpin? - ANSWER Critical structural member and connecting link between the chassis and the tractor fifth wheel.
What is the inspection criteria for kingpin? - ANSWER Excessive wear beyond acceptable limits; chipped, broken, or cracked collar; looseness in upper coupler construction
What is the required diameter of a kingpin? - ANSWER Upper section: between 2-
11/16" & 2-7/8"
Lower section: between 1-7/8" & 2"
What is the inspection criteria for the upper coupler plate? - ANSWER Examine for gouges from fifth wheel, lubricated with grease, excessive/uneven wear, dishing, bulging, or distortion upwards. Check for corrosion and/or blockage of drain holes.
What is the inspection criteria for the main rails? - ANSWER Sight along main rails to notice deformation (twist, bow, dent, or bend) in framework; examine frame welds for cracks
What is the deciding factor in repairing main rails? - ANSWER Rails must be repaired when deformation influences the ability of a container to be seated properly and secured to the chassis, or its ability to track properly.
What is the inspection criteria for the landing legs? - ANSWER Inspect support mounting brackets for bending and tight bolts; bolt holes on brackets and legs are same size; missing/damaged bolts replaced; uneven height; out of alignment (out of plumb condition in all directions)
What are the components of the landing gear? - ANSWER Landing leg brace (diagonal or cross brace), landing legs, gear box, cross shaft, crank handle, crank handle retainer, sand shoes (or wheels), sand shoe axle
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller michealmuthii. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $17.99. You're not tied to anything after your purchase.
Can Stuvia be trusted?
4.6 stars on Google & Trustpilot (+1000 reviews)
71184 documents were sold in the last 30 days
Founded in 2010, the go-to place to buy study notes for 14 years now