IICL Container Inspector's Exam Questions And Answers Rated A+ New Update Assured Satisfaction
4 views 0 purchase
Course
IICL Container Inspector\'s
Institution
IICL Container Inspector\'s
All corner posts, front and rear (Any single deformation such as bend, bow, dent, etc.) // Repair if -
more than 20 mm (13/16 in), regardless of length or location
Bottom side rails, front and door sills (Any deformation such as bend, bow, dent, etc. ON A WEB) //
Repair if - More than 50 mm (2 i...
IICL Container Inspector's Exam
All corner posts, front and rear (Any single deformation such as bend, bow, dent, etc.) // Repair if -
more than 20 mm (13/16 in), regardless of length or location
Bottom side rails, front and door sills (Any deformation such as bend, bow, dent, etc. ON A WEB) //
Repair if - More than 50 mm (2 in) deep
Of the following conditions in a dry-van container, which one would require cleaning?
A. Raised mud foot prints in excess of what might normally remain after a sweep out
B. Dry dust covering dried floor stains as might normally be found after a sweep out
C. Coffee beans remaining inside the container as might occur after a sweep out
D. Polyurethane beads as might be expected to lodge in grooves between floorboards after a sweep out
- C. Coffee beans remaining inside the container as might occur after a sweep out
An Equipment Interchange Receipt (EIR), based on an inspection with no damage found, can be evidence
of a container's compliance with: A. Australian Timber Component Treatment Regulations B. Convention
for Safe Containers (CSC) regulations through the ACEP Program
C. Transport under custom's seal (TIR) regulations D. International Standards Organization (ISO) CEDEX
codes regulations - B. Convention for Safe Containers (CSC) regulations through the ACEP Program
The top of a replacement plastic ventilator should be centered what distance from the top side rail? A.
50-55mm (2-2 3/16 in) B. 70-75mm (2 5/8 - 3 in)
C. 100mm (4in) D. 150mm (6 in) - A. 50-55mm (2-2 3/16 in)
When must a reference line extend the full length of a bottom side rail? A. When there are two or more
areas of damage on the bottom side rail B. When there is a sharp bend in the bottom side rail
C. When there is a bowing over the entire bottom side rail D. When there is additional damage to the
bottom side rail so that the reference line cannot be positioned over the ends of the damage - C.
When there is a bowing over the entire bottom side rail
,Which of the following is NOT a transverse structural member of the container?
A. Front sill B. Tunnel rail
C. Rear header
D. Crossmember - B. Tunnel rail
A steel corner fitting is being replaced. To ensure better weld penetration, IICL recommends that the
edges of parts adjacent to the corner fitting be ground to a minimum bevel of? A. 30 degrees B. 45
degrees
C. 55 degrees D. 60 degrees - B. 45 degrees
Which of the following components is sometimes placed longitudinally in the container to support
plywood flooring? A. Transverse bow B. Gusset
C. Hat section center spacer
D. Threshold plate - C. Hat section center spacer
Assuming owner and environmental regulations permit, which of the following procedures is NOT
recommended for repairing tarpaulins or open top containers? A. Cleaning the area to be covered with
acetone or mineral spirit B. Using a heat gun to fuse a patch to the tarpaulin C. Sewing on a patch of the
same material as the tarpaulin D. Repairing a 6 mm (1/4 in ) pin hole with an epoxy compound - C.
Sewing on a patch of the same material as the tarpaulin
Which of the following is an example of a plank floor condition requiring repair AND which should be
considered as damage?
A. A crack or split with no evidence of impact, which leaks light
B. A crack or split with a sign of impact which does not leak light
C. A crack or split, adjacent to a dented bottom rail, which leaks light
D. A crack or split, with no evidence of impact, with a loose piece - C. A crack or split, adjacent to a
dented bottom rail, which leaks light
Welds to corner fittings should be made with?
A. CO2 semi-automatic welding
, B. Low hydrogen welding rods
C. Fully automatic welding
D. Arc welding - B. Low hydrogen welding rods
All of the following procedures are required EXCEPT
A. Weld smoke, spatter, etc. must be removed to permit adhesion of paint
B. The damaged component(s) must be restored as close as possible to original size and profile
C. Welds must be examined using radiographic or magnetic particle non-destructive testing equipment
D. Replacement steel components must be painted with coating compatible with that originally applied
to the container - C. Welds must be examined using radiographic or magnetic particle non-
destructive testing equipment
Where should the reference line be placed in order to determine repairworthiness of a crossmember
flange that is bent upwards?
A. Along the inside lower formed edge of the crossmember
B. Spaced out from the crossmember web
C. On the outermost flange surface along the full crossmember length
D. No measurement is necessary - D. No measurement is necessary
The damaged top rail X below is to be repaired by sectioning. Care must be taken to ensure that damage
area X is NOT cut less than a minimum of
A. 50mm (2 in)
B. 100mm (4 in)
C. 150mm (6 in)
D. 200mm (9 in) - C. 150mm (6 in)
Door gaskets that are cut may be repaired by using cyanoacrylate adhesives to bond together the cut
edges of the gasket, PROVIDED
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller PatrickKaylian. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $7.99. You're not tied to anything after your purchase.
