100% satisfaction guarantee Immediately available after payment Both online and in PDF No strings attached
Previously searched by you
IICL Container Inspector's Exam Latest Update Actual Exam with 220 Questions and 100% Verified Correct Answers Guaranteed A+ Approved by the Professor$20.49
Add to cart
IICL Container Inspector's Exam Latest Update
2024-2025 Actual Exam with 220 Questions and
100% Verified Correct Answers Guaranteed A+
Approved by the Professor
____________________ repair a tarpaulin by sewing on a patch. - CORRECT
ANSWER: Do not
(understructure) When installing screws in a replacement understructure component,
use - CORRECT ANSWER: zinc-plated or other similarly treated self-tapping screws
with the same diameter of screw head and shank as the original
A "_____________________________" is defined as the outermost laminate (or outer 3
PLY pack of laminates) on either the top or bottom surface of the plywood. - CORRECT
ANSWER: surface veneer
A container ventilator consists of a plastic or steel cover approximately - CORRECT
ANSWER: 25 mm (1 in) in depth which is fitted over an area of the container side panel
in which holes have been drilled
A front corner post insert must be at least - CORRECT ANSWER: 150 mm (6 in) in
length, unless it terminates at a corner fitting
A front corner post insert that would terminate within 300 mm (12 in) of a corner fitting -
CORRECT ANSWER: must be extended to the fitting, and must be at least 200 mm (12
in) in length
A steel corner fitting is being replaced. To ensure better weld penetration, IICL
recommends that the edges of parts adjacent to the corner fitting be ground to a
minimum bevel of? A. 30 degrees B. 45 degrees
C. 55 degrees D. 60 degrees - CORRECT ANSWER: B. 45 degrees
,Accumulated scratches due to normal use of container. - CORRECT ANSWER: DV &
OT = No repair
All corner posts, front and rear (Any single deformation such as bend, bow, dent, etc.) //
Repair if - CORRECT ANSWER: more than 20 mm (13/16 in), regardless of length or
location
All corner posts, front and rear (OUTWARD deformation.) // Repair if - CORRECT
ANSWER: more than 5 mm (3/16 in) beyond plane of end surfaces or 10 mm (3/8 in)
beyond plane of side surfaces of corner fittings
All corner posts, including j-bars // Repair if - CORRECT ANSWER: Holed, cut, torn or
cracked; broken component and/or weld
All of the following procedures are required EXCEPT
A. Weld smoke, spatter, etc. must be removed to permit adhesion of paint
B. The damaged component(s) must be restored as close as possible to original size
and profile
C. Welds must be examined using radiographic or magnetic particle non-destructive
testing equipment
D. Replacement steel components must be painted with coating compatible with that
originally applied to the container - CORRECT ANSWER: C. Welds must be examined
using radiographic or magnetic particle non-destructive testing equipment
All rails, including side rails, headers and sills // Repair if.... - CORRECT ANSWER:
Holed, cut torn or cracked; broken component and/or weld // Missing or loose parts or
fasterners
All roof panels (DOWNWARD) deformation such as bend, dent, etc. // Repair if -
CORRECT ANSWER: IF more than 40 mm (1-9/16 in ) below top surfaces of top side
rails
, All roof panels (UPWARD) deformation such as bend, dent, etc. // Repair if - CORRECT
ANSWER: IF more than 40 mm (1-9/16 in ) above top surfaces of top side rails
All side/front panels // Repair if - CORRECT ANSWER: Holed, cut, torn or cracked;
broken component and/or weld
Missing or loose parts or fasteners
INWARD deformation such as bend, dent, etc. (if more than 35 mm (1-3/8 in), measured
on an exterior recessed corrugation)
All welds to corner fittings should be made with - CORRECT ANSWER: low-hydrogen
welding rods or wire in order to minimize any chances of hydrogen embrittlement in the
weld. (AWS E7016 and E7018 electrodes)
An Equipment Interchange Receipt (EIR), based on an inspection with no damage
found, can be evidence of a container's compliance with: A. Australian Timber
Component Treatment Regulations B. Convention for Safe Containers (CSC)
regulations through the ACEP Program
C. Transport under custom's seal (TIR) regulations D. International Standards
Organization (ISO) CEDEX codes regulations - CORRECT ANSWER: B. Convention for
Safe Containers (CSC) regulations through the ACEP Program
Anchor profile - CORRECT ANSWER: A term used to describe the arrangement of tiny
peaks and valleys on an abrasive-blasted surface to which paint will be applied
Anti-Rack Device - CORRECT ANSWER: Hardware normally attached to doors to
provide additional strength and stiffness to the door and end frame assembly. Such a
device allows containers to withstand greater transverse twisting (racking) forces
As a practical matter, it is _________________________ to detect differences between
instances of delamination and those of rolling-shear failure, unless the surface
veneer(s) are broken, without removal of the flooring (which is not done as a normal
part of inspection). - CORRECT ANSWER: not possible
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller Tutordiligent. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $20.49. You're not tied to anything after your purchase.
