Exam (elaborations)
ASFA NICET EXAM 1& 2 QUESTIONS AND ANSWERS
- Course
- Institution
ASFA NICET EXAM 1& 2 QUESTIONS AND ANSWERS
[Show more]
Content preview
ASFA NICET EXAM 1& 2 QUESTIONS AND ANSWERSWhat is the maximum area of coverage per sprinkler in an hydraulically calculated Extra
Hazard occupancy using standard spray uprights with a design density of 0.3 gpm/sq.
ft? - Answers -100 sq. ft
Determine the friction loss per foot of 250 gpm flowing in a 3 in. schedule 10 black steel
pipe installed in a dry pipe system. - Answers -0.078 psi/ft
What is the total combined inside and outside hose allowance required for hydraulically
calculated light hazard occupancies? - Answers -100 gpm
When residential sprinklers are installed throughout a compartment, what is the
minimum design density according to NFPA 13? - Answers -0.10 gpm/sq. ft
When calculating a light hazard occupancy with a remote area of 3000 sq. ft, what is the
minimum design density when no other area adjustments are made? - Answers -0.07
gpm/sq. ft
Based on an Oridinary hazard (Group 2) occupancy using a density of 0.20 gpm/sq. ft,
what is the minimum remote area required for a hydraulically calculated dry pipe system
with a ceiling height of 10 ft and a slope of 1 in 6? - Answers -1950 sq. ft
Determine the friction loss per foot of 1250 gpm flowing in a 6 in. CL ductile iron pipe
(Class 52) installed in a private fire main. - Answers -0.037 psi/ft
What is the minimum pressure required at the remote sprinkler in a light hazard system
using standard spray 5.6-K uprights covering 130 sq. ft? - Answers -7.0 psi
What factor is applied to 6 in. fittings installed in a wet system using schedule 10 black
steel pipe? - Answers -1.26
When sprinklers are omitted from combustible concealed spaces above isolated small
rooms not exceeding 55 sq. ft in a light hazard occupancy, what is the minimum design
area for a wet system installed in a building with a horizontal ceiling that is 22 ft high? -
Answers -1500 sq. ft
Quick response sprinklers are utilized in a dry pipe sprinkler system. What is the
allowable reduction in design area if the maximum ceiling height is 20 ft? - Answers -
25%
What is the equivalent length of a 4 in. flanged 90 degree elbow installed in a dry pipe
system using schedule 40 galvanized steel? - Answers -10 ft
, An Ordinary hazard (Group 1) wet system is installed in a 52,000 sq. ft building with a
horizontal ceiling. Sprinklers are uniformly spaced at 130 sq. ft (S=10, L=13). If a
density of 0.15 gpm/sq. ft is used, what is the minimum number of sprinklers required to
be calculated on a branch line if no area adjustments are made? - Answers -5
A fire pump is rated at 500 gpm @ 100 psi. What is the maximum allowable churn (no
flow) pressure? - Answers -140 psi
Which system type is permitted to have a paddle-type waterflow device installed? -
Answers -Wet
According to the abbreviations listed in NFPA 13, what characters represent a long turn
elbow? - Answers -Lt.E
What is the minimum required bolt size to hang 6 in. pipe from concrete? - Answers -1/2
in.
An office building is constructed exposed wood joist construction spaced 3 ft 10 in. on
center and has a depth of 6 in. What is the maximum protection area allowed for
standard spray upright sprinklers? - Answers -168
What is the minimum pitch required for cross mains installed on a dry pipe system
inside a flower storage cooler? - Answers -1/2 in. per 10 ft
What is the maximum room width for a standard spray sidewall installed along one side
of the mechanical room with combustible ceiling finishes? - Answers -10 ft
Which of the following is defined as an obstruction at or below the level of the sprinkler
deflector affecting the discharge of two or more sprinklers? - Answers -Continuous
obstruction
For a system installed utilizing residential sprinklers, what is the maximum total volume
permitted for an unprotected ceiling pocket? - Answers -100 cu. ft
A waterflow test is required to be conducted within 12 months of what project
milestone? - Answers -Working plan submittal
For a corrugated metal deck with a maximum depth of 4 in., the distance below the
ceiling is required to be measured from what point? - Answers -The highest point on the
deck
What is the minimum section modulus required for a trapeze hanger supporting 4 in.
schedule 10 pipe and spanning 5 ft? - Answers -0.43
Select all of the following data points that are required to graph a flow test. - Answers -
flow
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller GEEKA. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $12.49. You're not tied to anything after your purchase.
Can Stuvia be trusted?
4.6 stars on Google & Trustpilot (+1000 reviews)
80202 documents were sold in the last 30 days
Founded in 2010, the go-to place to buy study notes for 14 years now