Exam (elaborations)
API 570 - OPEN BOOK - PRACTICE EXAM 2024
- Course
- Institution
API 570 - OPEN BOOK - PRACTICE EXAM 2024
[Show more]
Content preview
API 570 - OPEN BOOK - PRACTICE EXAM 2024A Hydrotest is conducted on an underground line as a substitute for the external
inspection. The test pressure is 200 Psig. At the end of the test, the pressure must be at
least - API 570 9.8.6 - Answers -190 Psig.
Determine the maximum allowed pressure for a Class 300 flange that has a design
temperature of 950 °F. The flange material is ASTM A217 Gr. C12 - B16.5 Table 1.1-1 -
Answers -375 Psig.
An 8 NPS pipe is being replaced with A106 gr. B material. The pipe retirement thickness
(Tmin) is 0.218" and the corrosion allowance is 0.125". what is the minimum thickness
of pipe that could be ordered after adjusting for mill-tolerance? - API 574: 4.1.1 -
Answers -0.392"
A welder is being qualified by RT on a 0.600" plate using the SMAW process. What is
the maximum allowed length of an individual elongated slag inclusion for this qualifying
test? - ASME Sect. IX - QW-191.1.2.2(a)(2)(b) - Answers -0.200"
Protection in a boiler from Boiler Feed Water Corrosion is accomplished by: - API 571:
3.9.3.b - Answers -Maintaining a protective corrosion layer of magnetite (Fe3O4).
During the evaluation of a radiograph, the density at the IQI is 3.0. What is the minimum
density allowed on this radiograph in the weld? - ASME Sect V: T-282.2(a)(1) - Answers
-2.55
Which materials are generally Not susceptible to Acidic Sour Water Corrosion? This
may have more than one correct answer. Please select all answers that apply - API
571: 3.58.2.a&b - Answers -Copper, Nickel, Stainless Alloys
For Class 2 piping, a petrochemical plant should consider performing CUI inspections
at: API 570: Table 2 (pg. 48) - Answers -33% of the non-damaged areas.
The set pressure for a relief device protecting piping systems shall be set: ASME B31.3
- 322.6.3(b) - Answers -In accordance with the rules of ASME B&PV Section VIII.
When performing a WFMPT (Wet Fluorescent Magnetic Particle Testing) examination,
prior to the examination, the examiner shall be in a darkened area for. ASME Sect V. -
T-777.2(b) - Answers -5 Minutes
What is the maximum allowed hydrotest pressure for piping with class 300 flanges that
are made of ASTM 182 Gr. F316 Material? The Design Temperature is 600 °F - ASME
B16.5: 2.6, Tables 1.1-1 & 2-2.2c - Answers -1100 Psig.
, What is the required preheat temperature for an A106 Gr. B pipe with carbon content
less than 0.2% and has a wall thickness of 0.500"? - ASME B31.3: Table 330.1.1 -
Answers -50 °F
Atmospheric corrosion becomes less of an issue at temperatures above: - API 571 -
3.8.3.f - Answers -250 °F
Which of the following is an essential variable when qualifying a welder using the
SMAW process? - ASME Sect. IX - Table QW-416 or Table QW-353 - Answers -
Deletion of backing
Which document provides information on Integrity Operating windows? - API 570: 2 -
Answers -API 584
Without performing impact tests, what is the minimum allowed temperature for the
following piping system?
Material: A106 Gr. C
Nominal Thickness: 0.750"
Line Size: 6 NPS
Retirement Thickness: 0.500"
ASME B31.3: Table A-1, Table 323.2.2A - Answers -+ 15 °F
During the design of a pipe alteration, it is determined that impact testing of the pipe is
required. The pipe material is A106 Gr. C and is considered a fully deoxidized steel.
During impact testing all three specimens should break at or above: ASME B31.3: Table
323.3.5 - Answers -12 ft-lbs.
CS HAZ created - base metal temp during welding is: - API 577: 10.2.4 - Answers ->
1350 °F
30% solution of Caustic, PWHT Recommended for CS is: - API 571: Fig 3-15-1 -
Answers -≥ 140 °F
Minimum preheat temp for 5B mtl, with SMTS = 70 KSI is: - ASME B31.3 Table 330.1.1
- Answers -400 °F
Normal CS PWHT Temp is: - ASME B31.3: Table 331.1.1 - Answers -1100 - 1200 °F
A liquid penetrant procedure must be qualified when performing the examination: -
ASME Sect. V - T-653 - Answers -On Materials below 40 °F
When qualifying a SMAW weld procedure, if the "A-Number" on the PQR is an A-2,
what "A-Number" must be on the WPS? - ASME Sect. IX - Table QW-253 & QW-404.5 -
Answers -A-1 or A-2
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller GEEKA. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $12.49. You're not tied to anything after your purchase.
Can Stuvia be trusted?
4.6 stars on Google & Trustpilot (+1000 reviews)
81989 documents were sold in the last 30 days
Founded in 2010, the go-to place to buy study notes for 14 years now