Binding U-Joint will damage?? - ANSWER-Extension housing bushing
and seal
What is used to check the clearance between the shift fork and the
synchronizer sleeve? - ANSWER-A feeler guage
Warped pressure plates... - ANSWER-... should be replaced
Ring and pinion gears... - ANSWER-...should be replaced as a set
What tool is used to measure ring gear runout? - ANSWER-A dial
guage
,How many times can a collapsible sleeve be tightened? – ANSWER-
Once, and must be replaced if over tightened.
What tool is used to check pinion bearing preload? - ANSWER-Inch
pound torque wrench
How much vacuum is required to operate a transfer case? - ANSWER-
15hg
What type of bearings require preload? - ANSWER-Tapered roller
bearings
Can a bad speed sensor affect shift pattern? - ANSWER-Yes
What is a viscous clutch designed for? - ANSWER-Compensating for
differences in axle rotation
What kind of noise will chipped gear teeth make? - ANSWER-Growling
or grinding noise
Bell housing transmission bore and the rear face should be checked
for? - ANSWER-Runout
Check runout before or after installing pressure plate cover? -
ANSWER-Before
Correct face runout by... - ANSWER-Installing shims
,Symptoms of a stuck pilot bearing? - ANSWER-Clutch not
disengaging
Noise
Clutch hub damage
Mark position of flywheel in relation to... - ANSWER-Crankshaft
Whining gears can be caused by..... - ANSWER-Low fluid
Worn bearings will make what type of noise? - ANSWER-Growl or
grating
If a noise is loudest on corners then the noise is most likely coming
from... - ANSWER-Axle bearings
Diff Gears
Final drive case bearings
Gear noise in only one gear - ANSWER-Constant mesh gear
combination for that gear damaged
Clunk on acceleration and deceleration most likely cause... -
ANSWER-Worn differential pinion shaft or side gear or worn drive
axle inner joints.
, Hard shifting - ANSWER-Excessive shift effort, sleeve not sliding over
blocking ring and gear teeth
Jumping out of gear - ANSWER-Excessive wear in synchronizer
inserts, springs, shift forks or shift rails or countershaft Blockout -
ANSWER-Gear cones worn, blocking ring worn
What isn't noticible in 4th gear? - ANSWER-Worn main drive gear
bearing.
When inspecting shift linkage always replace? - ANSWER-...Bushings
Differential case preload maintains... - ANSWER-...Ring gear position
What type of axle has bearings on the axle housing that supports the
vehicle's weight? - ANSWER-Full floating axle
Slip yoke is lubed by? - ANSWER-Transmission fluid in transmission
Driveshaft imbalance can sometimes be solved by... – ANSWER-
Rotating the shaft and reinstalling.
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller nyagajoseph539. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $27.99. You're not tied to anything after your purchase.
