100% satisfaction guarantee Immediately available after payment Both online and in PDF No strings attached
logo-home
Mobile water supply Questions and Answers 2024 $14.49   Add to cart

Exam (elaborations)

Mobile water supply Questions and Answers 2024

 2 views  0 purchase
  • Course
  • Mobile water supply
  • Institution
  • Mobile Water Supply

Exam of 5 pages for the course Mobile water supply at Mobile water supply (Mobile water supply)

Preview 2 out of 5  pages

  • September 27, 2024
  • 5
  • 2024/2025
  • Exam (elaborations)
  • Questions & answers
  • Mobile water supply
  • Mobile water supply
avatar-seller
jw638729
Mobile water supply

You are stationed in Alaska in December. You've just come back from a company
inspection to find that your stall door will not operate and cannot be fixed until the
following day. To prevent damage from freezing you should: - answerDrain the piping,
pump, and booster lines to prevent damage.

When testing the priming device on an MWS apparatus with a fire pump with a capacity
less than 1,500 gpm, the priming device should be able to create the necessary vacuum
in 30 seconds to lift water 10 feet through: - answer20 feet of hard suction hose.

identify FOUR pre-service for an MWS apparatus equipped with a fire pump. -
answer•Road test
• Independent pump certification tests
• Purchase acceptance tests
• Hydrostatic tests

Identify THREE items that are checked for leaks during the vacuum test. -
answer•Priming device
• Hard suction hose
• Pump

Identify THREE pieces of equipment needed to conduct service testing on an MWS
apparatus equipped with a fire pump. - answer•Tachometer
•Smoothbore tips
•External test gauges

When performing a vacuum service test, once the engine is turned off, the column of
mercury should fall no more than: - answer10 inches in 5 minutes

Tracking engine performance across time uses data collected in the: - answerFuel, oil,
and mileage record.

Identify THREE critical items that should be included on an MWS apparatus daily
inspection checklist. - answer•Apparatus unit identification number
•Inspected by column
•Remarks column

An MWS apparatus should be started with all electrical switches in the OFF position in
order to: - answerStart the engine without a load.

During MWS apparatus service testing, the atmospheric air temperature should be
between: - answer0F-100F

, NFPA 1911 requires an MWS apparatus equipped with a fire pump to be service tested:
- answerAt least once a year or when it has undergone extensive pump repair.

The pressure control service test measures pressure control devices at three different
points. They are: - answer90 psi, 150 psi, and 250 psi.

When maintaining MWS apparatus records, you should: - answerRefer to your dept.
SOPs for specific guidance.

Before you drive an MWS apparatus across a bridge, you should: - answerCompare the
weight of the MWS apparatus to the bridge's capacity.

All of the following statements about parking an MWS apparatus near a railroad track
are true EXCEPT: - answerPark on the opposite side of the tracks as the incident.

Starting an MWS apparatus in the correct order: - answer1. Disconnect all aux.
electrical & air sources.
2. Turn on apparatus battery
3.Start the engine
4.Observe the gauges
5.Check seat, mirrors, and steering wheel
6.Check that all crew members have fastened their seat belts

The definition of lift is: - answerThe vertical distance from the surface of the water to the
middle of the intake.

Place the codes hydrants in order of capacity from LEAST capacity to GREATEST. -
answer1. Red
2. Orange
3. Green
4. Light blue

Identify TWO correct statements about hydrants: - answer• Grid systems with large
supply mains and looping secondary mains generally have less friction.

• if hydrants are color-coded, select a light blue hydrant when responding to a large
incident and be sure to test the flow before connecting the hydrant to the fire pump.

What is the minimum required intake pressure of the apparatus being re supplied? -
answer20 psi

If water is flowing through 100 feet of a 4-inch hose at 500 gpm, then the friction loss is
approximately: - answer5 psi

As hose diameter increases: - answerFriction loss DECREASES

The benefits of buying summaries with Stuvia:

Guaranteed quality through customer reviews

Guaranteed quality through customer reviews

Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.

Quick and easy check-out

Quick and easy check-out

You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.

Focus on what matters

Focus on what matters

Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!

Frequently asked questions

What do I get when I buy this document?

You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.

Satisfaction guarantee: how does it work?

Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.

Who am I buying these notes from?

Stuvia is a marketplace, so you are not buying this document from us, but from seller jw638729. Stuvia facilitates payment to the seller.

Will I be stuck with a subscription?

No, you only buy these notes for $14.49. You're not tied to anything after your purchase.

Can Stuvia be trusted?

4.6 stars on Google & Trustpilot (+1000 reviews)

78310 documents were sold in the last 30 days

Founded in 2010, the go-to place to buy study notes for 14 years now

Start selling
$14.49
  • (0)
  Add to cart