Exam (elaborations)
W47.1 PRACTICE 1 QUESTIONS AND ANSWERS
- Course
- Institution
W47.1 PRACTICE 1 QUESTIONS AND ANSWERS
[Show more]
Content preview
W47.1 PRACTICE 1 QUESTIONS AND ANSWERSCSA Standard W47.1 provides the requirements that must be met and adhered to by a
company seeking certification. - Answers-True
CSA Standard W47.1 provides the requirements that must be met and adhered to by a
company seeking certification - Answers-True
Certification can be considered as an approval of the products fabricated by a certified
company - Answers-False
What does Class refer to? - Answers-F,H,V & O welding positions flat (F), horizontal
(H), vertical (V), or overhead (O) positions.
How many divisions of certification are specified in CSA W47.1? - Answers-Three
Division 3 — the company is not required to employ or retain a welding engineer. -
Answers-
For Division 1 companies does the welding engineer need to be situated at the
company? - Answers-No
Division 1 - Answers-The company shall employ a welding engineer on a full time basis
Is a company certified in Division 3 required to employ a full time or retain a part-time
welding engineer? - Answers-No welding engineer is required.
Division 2 - Answers-The company shall retain a welding engineer on a part time basis
CSA W47.1 requires each designated plant, shop or section to meet the requirements
of certification within this standard with respect to welder, welding procedure
specifications, welding procedure data sheets, welding supervisor and welding
engineer, where applicable - Answers-True
A company doing only erection work involving welding must have a plant in order to be
certified to CSA W47.1. - Answers-False
When must the company inform the CWB of any loss or change in welding engineering
or supervisory personnel? - Answers-Immediately
The company shall designate an individual who, irrespective of other responsibilities,
shall have defined authority and responsibility for ensuring that the requirements of CSA
W47.1 are implemented and maintained. - Answers-True
A welding supervisor with two years of fabrication experience is acceptable for a
Division 1 company. - Answers-False It is a minimum of 5 years
, Each supervisor shall have knowledge of: - Answers-Weld Faults and Quality Control
Each supervisor shall be able to read drawings and properly interpret welding symbols.
- Answers-True
Who is responsible for ensuring the welders weld in accordance with approved or
accepted welding procedure data sheets in the shop and field? - Answers-The welding
supervisor
What are the duties of the welding engineer? - Answers-Provide engineering support to
the company as required, Development of new welding procedures, Preparation of
WPSs and WPDSs, Periodic reviews of the companies welding practices
What type of identification cards are issued to welders by the CWB? - Answers-A
transferable id card when qualification is based on standard test assemblies, A
nontransferable id card when qualification is based on non -standard test assemblies, A
letter in lieu of an id card
Who owns the welder cards that are issued by the CWB? - Answers-The CWB
Who is responsible for ensuring the welders ID cards or copies thereof can be produced
as proof that a welder has valid qualifications? - Answers-The company
Which of the following electrodes is a group F4 electrode? - Answers-EXX18
Tack welders must be qualified. 8.3.2 (Welding personnel) - Answers-True
If there is a reason to doubt a welder's ability, his/her qualification is suspended
immediately and they shall be required to pass a check test in the position and class
held. - Answers-True
To what type of welding is a probationary welder restricted? - Answers-Welding flat
grooves and flat horizontal fillets under supervision
A change in the mode of metal transfer from short circuiting to spray or globular for the
GMAW process requires a separate qualification. - Answers-True
Welding on galvanized surfaces requires a separate qualification: - Answers-True
Electrodes used for welding personnel qualification tests shall be certified by the CWB
as conforming to the requirements of the latest CSA W48 or the appropriate AWS A5
series of standards. - Answers-True
If a welder has qualified on a standard test assembly, what range of material thickness
is he/she now qualified to weld? - Answers-3 mm (1/8") and thicker
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller GEEKA. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $11.09. You're not tied to anything after your purchase.
Can Stuvia be trusted?
4.6 stars on Google & Trustpilot (+1000 reviews)
81503 documents were sold in the last 30 days
Founded in 2010, the go-to place to buy study notes for 14 years now