API 570 Exam Questions With Revised Correct Detailed Answers Guaranteed Pass
5 views 0 purchase
Course
API 570
Institution
API 570
API 570 Exam Questions With
Revised Correct Detailed Answers
Guaranteed Pass
1) What is the interval for thickness measurements on a class 1 piping system? -
ANSWER
lesser of 5 years or half life of the pipe
2) According to B31.3, a welder's qualification records from a previous em...
API 570 Exam Questions With
Revised Correct Detailed Answers
Guaranteed Pass
1) What is the interval for thickness measurements on a class 1 piping system? -
ANSWER lesser of 5 years or half life of the pipe
2) According to B31.3, a welder's qualification records from a previous employer
can: - ANSWER Be accepted if the inspector approves
3) When welding together piping components of different thicknesses, the thicker
part should be trimmed with a: - ANSWER 30 degree taper.
4) When performing soil-to air inspections on uncoated lines, it is recommended
to excavate the soil: - ANSWER 6-12 inches.
5) When performing preheat prior to welding or PWHT, the preheat zone and/or
PWHT must extend how far beyond the edge of the weld? - ANSWER 1 inch
6) Flange bolts are unacceptable if the bolt threads do not extend: - ANSWER
inside the nut within 1 thread of the nut face
7) Carbon steel materials are most likely to be incorrectly substituted in: -
ANSWER a chrome steel piping system.
,8) Per B31.3 how much of the fabrication should be visually examined for a pipe
in severe cyclic service: - ANSWER 100 %
9) When calibrating a UT instrument, that has a delay line with single element
unit, use: - ANSWER At least 2 test blocks with thicknesses near the max and
min to be examined.
10) During pipe repairs, which welding discontinuity is always unacceptable? -
ANSWER Cracks and Inadequate fusion
11)1 What do you call a groove in the parent metal at the toe of a weld? -
ANSWER undercut
12) The RT procedure used for a pipe repair must conform to the requirements of:
- ANSWER ASME Section 5
13) What is the minimum holding time for all pressure tests on piping? - ANSWER
10 mins
14) When a relief device or valve is removed for repair, the inspector should: -
ANSWER inspect the inside of the inlet and outlet piping where the valve was
removed.
15) Thickness measurements are suggested at pipe fittings since: - ANSWER
directional changes generally create increased turbulence and corrosion.
, 16) Flange leaks in certain fluids can cause: - ANSWER bolts to crack and
corrode
17) Heat Tracing could cause cracking in carbon steel piping which is in: -
ANSWER Caustic service
Excessive repairs to pump bearings may be a result of: - ANSWER thermal
growth
Loose or broken anchor bolts at pipe supports are most easily detected by: -
ANSWER hammer testing
A pneumatic pressure test is to be conducted on a Normal Service piping system.
During pipe erection, how many of the joint assemblies should be examined? -
ANSWER 100 %
During a pipe repair, preheat is substituted for the required PWHT. What is the
minimum preheat temperature. - ANSWER 300°
Minimum time an examiner should be in a darkened area prior to using a black
light when performing MT & PT exam - ANSWER 5 min
The corrosion rate for newly installed piping systems or for changes in service
must be established. API 570 provides three methods of determination probable
corrosion rates for these conditions. - ANSWER API 570 paragraph 7.1.2
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller NURSINGDICTIONARY. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $11.34. You're not tied to anything after your purchase.
