100% satisfaction guarantee Immediately available after payment Both online and in PDF No strings attached
logo-home
ASE Brakes A5 Test ( Exam 1 ), ASE A5 Brakes, ASE Brakes A5 ( Exam 3 ), ASE Brakes A5 Test ( Exam 2 ) EXAM 2025 QUESTIONS AND CORRECT ANSWER $17.99   Add to cart

Exam (elaborations)

ASE Brakes A5 Test ( Exam 1 ), ASE A5 Brakes, ASE Brakes A5 ( Exam 3 ), ASE Brakes A5 Test ( Exam 2 ) EXAM 2025 QUESTIONS AND CORRECT ANSWER

 5 views  0 purchase
  • Course
  • ASE Brakes A5 Te 1 ), ASE A5 Brakes, ASE
  • Institution
  • ASE Brakes A5 Te 1 ), ASE A5 Brakes, ASE

ASE Brakes A5 Test ( Exam 1 ), ASE A5 Brakes, ASE Brakes A5 ( Exam 3 ), ASE Brakes A5 Test ( Exam 2 ) EXAM 2025 QUESTIONS AND CORRECT ANSWER

Preview 4 out of 82  pages

  • October 22, 2024
  • 82
  • 2024/2025
  • Exam (elaborations)
  • Questions & answers
  • ase a5 brakes ase
  • ASE Brakes A5 Te 1 ), ASE A5 Brakes, ASE
  • ASE Brakes A5 Te 1 ), ASE A5 Brakes, ASE
avatar-seller
dennohz2000
ASE Brakes A5 Test ( Exam 1 ), ASE A5 Brakes, ASE Brakes A5 ( Exam 3 ), ASE
Brakes A5 Test ( Exam 2 ) EXAM 2025 QUESTIONS AND CORRECT ANSWER
Technician A says a cracked brake hose that is not

leaking need not be replaced. Technician B says a

brake hose with a blister must be replaced. Who is

right?



a. A only

b. B only

c. Both A and B

d. Neither A nor B - answer>>>b



A drum is chattering on the brake lathe. This could be a result of



a. failure to install the dampening belt

b. cutting too slowly

c. dull cutting blades

d. cutting speed too fast - answer>>>A : failure to install the dampening belt



why : a missing dampening belt could cause the drum to vibrate while on the lathe. this vibration can
cause the drum to bounce on the cutting tip and make a chattering noise



Brake pedal reserve that gradually fades under light

pressure indicates:



a. Leaks in the brake lines

b. Weak brake pedal return spring tension

c. Internal leaks

d. The system is operating properly - answer>>>c

,Which of the following is NOT a method used to force

air and contaminated fluid out of a brake system?



a. Manual brake bleeding

b. Pressure tank bleeding

c. Vacuum bleeding

d. Bench bleeding - answer>>>d



The first component in a brake system bleeding

sequence is the:



a. Master cylinder

b. Wheel cylinder

c. Combination valve

d. Proportioning valve - answer>>>a



The quick-take-up (QTU) valve on a master cylinder

regulates fluid flow:



a. Between the master cylinder and the reservoir

b. Between the reservoir and the pushrod

c. Between opposite wheels

d. Between the two hydraulic circuits of the system - answer>>>a



Floating drums may be held in place by all of the

following EXCEPT:



a. Speed nuts over the wheel studs

,b. Bolts threaded into the hub

c. The wheel and lug nuts

d. A castellated spindle nut - answer>>>d



To detect an out-of-round brake drum, measure it with

a:



a. Drum micrometer

b. Drum gauge

c. Drum dial indicator

d. Shoe setting caliper - answer>>>a



On calipers with fixed seals, most manufacturers

recommend a caliper to bore clearance of:



a. .001-.006 inch for metal pistons; .0005-.0015 for

aluminum pistons

b. .002-.003 inch for aluminum pistons; .003-.007 inch for

phenolic pistons

c. .004-.006 inch for metal pistons; .002-.006 inch for

phenolic pistons

d. .002-.005 inch for metal pistons; .005-.010 inch for

phenolic pistons - answer>>>d



True or False: Some calipers can require special tools

to retract the piston.



a. True

b. False - answer>>>a

, On calipers with stroking seals, most manufacturers

specify a caliper piston-to-bore clearance of:



a. 0.004 to 0.006 inch (mm)

b. 0.004 to 0.008 inch (mm)

c. 0.004 to 0.010 inch (mm)

d. 0.004 to 0.014 inch (mm) - answer>>>c



A dial indicator can be used to check a brake rotor

for:



a. Radial runout

b. Parallelism

c. Taper variation

d. Lateral runout - answer>>>d



Technician A says that when turning drums or rotors,

both components on the same axle must be

machined to the same tolerance. Technician B says

that the least amount of metal should be removed

during machining. Who is right?



a. A only

b. B only

c. Both A and B

d. Neither A nor B - answer>>>b



Technician A says that a new bearing should never be

The benefits of buying summaries with Stuvia:

Guaranteed quality through customer reviews

Guaranteed quality through customer reviews

Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.

Quick and easy check-out

Quick and easy check-out

You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.

Focus on what matters

Focus on what matters

Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!

Frequently asked questions

What do I get when I buy this document?

You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.

Satisfaction guarantee: how does it work?

Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.

Who am I buying these notes from?

Stuvia is a marketplace, so you are not buying this document from us, but from seller dennohz2000. Stuvia facilitates payment to the seller.

Will I be stuck with a subscription?

No, you only buy these notes for $17.99. You're not tied to anything after your purchase.

Can Stuvia be trusted?

4.6 stars on Google & Trustpilot (+1000 reviews)

83637 documents were sold in the last 30 days

Founded in 2010, the go-to place to buy study notes for 14 years now

Start selling
$17.99
  • (0)
  Add to cart