ABO Certification Exam Solved Questions With Revised Correct Detailed Answers
13 views 0 purchase
Course
ABO
Institution
ABO
ABO Certification Exam
Solved Questions With Revised
Correct Detailed Answers
1. How would you move a temple if the front is lower on the right? - ANSWER Bend the right one down
2. What type of lens can be used to test prism in a patient's glasses? - ANSWER Fresnel
3. Positive fac...
ABO Certification Exam
Solved Questions With Revised
Correct Detailed Answers
1. How would you move a temple if the front is lower on the right?
- ANSWER Bend the right one down
2. What type of lens can be used to test prism in a patient's glasses?
- ANSWER Fresnel
3. Positive face form means the frame is bent ________.
- ANSWER The frame front bends toward the face.
4. Cellulose acetate will shrink slight if _____ and _______ quickly.
- ANSWER Heated, cooled
5. This metal is very durable but difficult to make and usually cannot be
soldered.
- ANSWER Titanium
6. The ED of a frame is ___________.
- ANSWER Twice the longest radius from the geometric center of the lens.
, 7. If the metal frames on a patient are sitting too high, you would?
- ANSWER Widen the pads
8. The bottom of the pads on a pair of glasses are too close to the eye, which
angle will you change to bring them forward?
- ANSWER Veritcal
9. If the left temple is bent upward:
- ANSWER The right side of the front will raise.
10.How can you correct a pair of glasses if they are touching the brow?
- ANSWER Lengthen the pad arms.
11.What is the axis tolerance for 2015 ANSI standards for a 1.00 cyl?
- ANSWER +/- 3 deg
12. A pair of progressives were ordered at a 22 seg ht, they came in with a seg of
21 and 23. What is the tolerance allowed for seg heights for a progressive?
- ANSWER 1.0 mm
13. For the impact tested safety eyewear, how fast is the ball moving during the
test? - ANSWER 150 ft/sec
14. A lens was ordered as a +1.50 -.75 X 23. What is the axis tolerance for this
lens? - ANSWER +/- 5 deg
, 15. How far is a ball dropped in a drop ball test? - ANSWER 50 inches
16. A pair of single vision lenses came in a metal frame, The PD is wide by 2 mm in
the right eye. The RX for this lens is +2.25. How much prism is being induced and
is this within tolerance? - ANSWER Prism is 0.45 D, yes
17. What is the tolerance for a specified base curve on a pair of glasses? -
ANSWER 0.75 D
18. The tolerance on a progressive lens sphere of -8.00 to +8.00 is _____________
diopter? 0.16D
What size of the steel ball used on a basic drop ball test?
5/8 inch
What is the tolerance for a cylinder greater than 1.50D?
+/- 2.00
A safety lens is being drop ball tested. What is the size of the ball?
1 inch
What is the tolerance for a fitting height in a progressive lens? 1.0mm
What is the tolerance for the sphere power in a SV lens that is -6.50?
+/- 0.13 D
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller TOPPLUGGER. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $11.34. You're not tied to anything after your purchase.
