NACE CIP Level 1 Sample Quizes Questions
With Answers 100% Correct
The anode is the part of the metal that corrodes
General corrosion is described as uniform loss of thickness over the exposed surface
In order to reach consensus and to resolve conflict on the job, the NACE Inspector's preferred
course of action is to actively listen and endeavor to understand the postions of others.
A proper coating specification should contain information regarding surface preparation
standards, safety, locations to be coated
According to the NACE attestation, it's OK to accept a gift from a contractor as long as the gift is
below the value identified in your company policy. false
If an inspector finds discrepancies between the specification and the coating manufacturers
technical data sheet, the preferred coarse of action is to seek written clarification from the
specifier
,NACE CIP Level 1 Sample Quizes Questions
With Answers 100% Correct
All of the following are generally included within inspection reports EXCEPT cost
information
Inspectors reports provide sufficient detail permitting the owner to evaluate contractor's
performance, inspector's performance, job progress, work interruptions
When applying coatings, instruction regarding appropriate types of Personal Protection
Equipment (PPE) will always be found within the material safety data sheet (MSDS) or
safety data sheet (SDS)
Material inventory report should contain all of the following EXCEPT overall cost of
materials
Safety enforcement is one of the primary responsibilities of the coating inspector false
If the relative humidity is too high, solvent entrapment within the coating film may occur.
true
, NACE CIP Level 1 Sample Quizes Questions
With Answers 100% Correct
The dew point is the temperature at which moisture condenses on a surface.
Steel surface temperature reading should be taken at the actual work locations
The coatings inspector must calibrate the magnetic surface thermometer at the job site.
False
If solvent is trapped in a coating film it may cause problems with the curing of the film.
Electronic Surface Contact Thermometers do not require stabilization prior to use
MOST coatings in the industrial and marine field are inorganic coatings? False
The predominant pigment in sacrificial coating is zinc
The vehicle of a coating consists of solvent, binder, and liquid additivess
With Answers 100% Correct
The anode is the part of the metal that corrodes
General corrosion is described as uniform loss of thickness over the exposed surface
In order to reach consensus and to resolve conflict on the job, the NACE Inspector's preferred
course of action is to actively listen and endeavor to understand the postions of others.
A proper coating specification should contain information regarding surface preparation
standards, safety, locations to be coated
According to the NACE attestation, it's OK to accept a gift from a contractor as long as the gift is
below the value identified in your company policy. false
If an inspector finds discrepancies between the specification and the coating manufacturers
technical data sheet, the preferred coarse of action is to seek written clarification from the
specifier
,NACE CIP Level 1 Sample Quizes Questions
With Answers 100% Correct
All of the following are generally included within inspection reports EXCEPT cost
information
Inspectors reports provide sufficient detail permitting the owner to evaluate contractor's
performance, inspector's performance, job progress, work interruptions
When applying coatings, instruction regarding appropriate types of Personal Protection
Equipment (PPE) will always be found within the material safety data sheet (MSDS) or
safety data sheet (SDS)
Material inventory report should contain all of the following EXCEPT overall cost of
materials
Safety enforcement is one of the primary responsibilities of the coating inspector false
If the relative humidity is too high, solvent entrapment within the coating film may occur.
true
, NACE CIP Level 1 Sample Quizes Questions
With Answers 100% Correct
The dew point is the temperature at which moisture condenses on a surface.
Steel surface temperature reading should be taken at the actual work locations
The coatings inspector must calibrate the magnetic surface thermometer at the job site.
False
If solvent is trapped in a coating film it may cause problems with the curing of the film.
Electronic Surface Contact Thermometers do not require stabilization prior to use
MOST coatings in the industrial and marine field are inorganic coatings? False
The predominant pigment in sacrificial coating is zinc
The vehicle of a coating consists of solvent, binder, and liquid additivess
