NCCER Electrical 1 Module 10 complete
with Questions and correct Answers
Blue Prints - correct answer-✅An exact copy of reproduction of an original drawing
Floor plan - correct answer-✅As viewed from above
Site plan - correct answer-✅Location of building on the property
Surveys show - correct answer-✅All property lines, existing public utilities and their location on or near
the property
Elevation drawings show - correct answer-✅The exterior face of the building
Floor plans are in - correct answer-✅2 dimension, length and width
Topographic survey shows - correct answer-✅Property lines, contour lines, notes and symbols
Sectional view - correct answer-✅Is a cutaway view that shows the inside of the building
Title block - correct answer-✅A table located in the bottom right-hand corner of an engineering drawing
that identifies, in an organized way, all of the necessary information that is not given on the drawing
itself. Also referred to as a title strip.
Revision Block - correct answer-✅Shows modifications or redrawn drawings
Architectural scale - correct answer-✅1/16" = 1', 1/8" = 1' 1/4" = 1
Engineer scale measurements - correct answer-✅1"=10 units through 1"=100 units
Metric scale 1:1 to 1:100 - correct answer-✅Millimeters are used
Metric scale 1:200 to 1:2000 - correct answer-✅Meter is used
CAD - correct answer-✅Computer aided design
Masterformat - correct answer-✅Most common used writing format
Division 26 is - correct answer-✅Electrical
Division 27 is - correct answer-✅Communications
Division 28 is - correct answer-✅Electronic safety and security
ANSI - correct answer-✅American National Standards Institute
The type of lighting fixture is identified by - correct answer-✅A numeral placed inside a triangle or other
symbol and placed near the fixture to be identified
A section line on a drawing shows - correct answer-✅The location of the section on the plan
In a drawing with dimension lines the values shown inside the lines are - correct answer-✅The actual
dimensions
Dashed lines are used to represent a branch circuit on a drawing mean that the wiring is to be - correct
answer-✅Concealed in the floor
And electrical drafting line with a double arrowhead represents - correct answer-✅A branch circuit
homerun
To meet general recommendations a residential branch circuit rated for 2400 VA should have a
connected load of no more than - correct answer-✅1,920VA
Power riser diagrams are used to show the - correct answer-✅Arrangement of electric service
equipment
The symbols T1 T2 and T3 in a typical motor starter schematic represent - correct answer-✅Motor
terminals
The current master format standard covering communications systems is under - correct answer-
✅Division 27
Title Block on electrical drawing includes - correct answer-✅Name of the project, address of the
project, name of the owner of client, name of the architectural firm, date of completion, scale, initials of
the drafter, checker, and designer with dates under each, job number, sheet number, general description
of the drawing
with Questions and correct Answers
Blue Prints - correct answer-✅An exact copy of reproduction of an original drawing
Floor plan - correct answer-✅As viewed from above
Site plan - correct answer-✅Location of building on the property
Surveys show - correct answer-✅All property lines, existing public utilities and their location on or near
the property
Elevation drawings show - correct answer-✅The exterior face of the building
Floor plans are in - correct answer-✅2 dimension, length and width
Topographic survey shows - correct answer-✅Property lines, contour lines, notes and symbols
Sectional view - correct answer-✅Is a cutaway view that shows the inside of the building
Title block - correct answer-✅A table located in the bottom right-hand corner of an engineering drawing
that identifies, in an organized way, all of the necessary information that is not given on the drawing
itself. Also referred to as a title strip.
Revision Block - correct answer-✅Shows modifications or redrawn drawings
Architectural scale - correct answer-✅1/16" = 1', 1/8" = 1' 1/4" = 1
Engineer scale measurements - correct answer-✅1"=10 units through 1"=100 units
Metric scale 1:1 to 1:100 - correct answer-✅Millimeters are used
Metric scale 1:200 to 1:2000 - correct answer-✅Meter is used
CAD - correct answer-✅Computer aided design
Masterformat - correct answer-✅Most common used writing format
Division 26 is - correct answer-✅Electrical
Division 27 is - correct answer-✅Communications
Division 28 is - correct answer-✅Electronic safety and security
ANSI - correct answer-✅American National Standards Institute
The type of lighting fixture is identified by - correct answer-✅A numeral placed inside a triangle or other
symbol and placed near the fixture to be identified
A section line on a drawing shows - correct answer-✅The location of the section on the plan
In a drawing with dimension lines the values shown inside the lines are - correct answer-✅The actual
dimensions
Dashed lines are used to represent a branch circuit on a drawing mean that the wiring is to be - correct
answer-✅Concealed in the floor
And electrical drafting line with a double arrowhead represents - correct answer-✅A branch circuit
homerun
To meet general recommendations a residential branch circuit rated for 2400 VA should have a
connected load of no more than - correct answer-✅1,920VA
Power riser diagrams are used to show the - correct answer-✅Arrangement of electric service
equipment
The symbols T1 T2 and T3 in a typical motor starter schematic represent - correct answer-✅Motor
terminals
The current master format standard covering communications systems is under - correct answer-
✅Division 27
Title Block on electrical drawing includes - correct answer-✅Name of the project, address of the
project, name of the owner of client, name of the architectural firm, date of completion, scale, initials of
the drafter, checker, and designer with dates under each, job number, sheet number, general description
of the drawing
