100% satisfaction guarantee Immediately available after payment Both online and in PDF No strings attached
logo-home
Alberta welding first year final AIT exam Questions with Explanations of Answers | latest upate 2024 £6.46   Add to cart

Exam (elaborations)

Alberta welding first year final AIT exam Questions with Explanations of Answers | latest upate 2024

 8 views  0 purchase

Alberta welding first year final AIT exam Questions with Explanations of Answers | latest upate 2024

Preview 2 out of 5  pages

  • June 17, 2024
  • 5
  • 2023/2024
  • Exam (elaborations)
  • Questions & answers
All documents for this subject (107)
avatar-seller
ACTUALSTUDY
Alberta welding first year final AIT exam
A Material Safety Data Sheet must be reviewed whenever new information becomes available
or at least how often? - every three years

What is the total number of hours of work experience, including technical training, required per
year in the Welder Apprenticeship Program? - 1800

Voltage-sensing wire feeders set their speed according to: - arc voltage.

How much electrode stickout is recommended when using gas shielded FCAW with 1.2 mm
(0.045") wire? - 10 mm to 19 mm (3/8" to 3/4")

One of the main functions of the contact tube is to: - transfer current to the electrode.

Flame propagation means the speed at which the fuel gas will travel - False

What height limitation is in place when using freestanding scaffolding? - For free standing
scaffolds, the scaffold must not be taller than three (3) times its smallest dimension in height

The best reference point for dimensioning on pressure vessels is the: - datum line

Which of the following is an abbreviation of a Non destructive test ? - UT

In common fabricating practice, there are how many basic joint types? - 5

Single "V" butt joints are used on material thicknesses of: - 3/8" -1" (9.5 -25.4mm)

A small change in sling angle can drastically affect the: - sling load.

The power sources used for pulsed spray transfer are: - DC synergic,
microprocessor-controlled.

Single "V" butt joints are used on material thicknesses of: - 3/8" -1" (9.5 -25.4mm)

If you must apply force to a suspended load, always pull the load towards you. -

When installing clips, the saddle side of the clip must be placed on the: - Live side of the wire

When balancing a No. 2 welding tip and the acetylene torch needle valve is fully open, the
acetylene regulator should be adjusted so that the flame blows away from the tip _______ inch.
(Oxygen needle valve is closed) - 1/4

, Which ferrous-based metals cannot be cut satisfactorily with an oxy-fuel cutting torch? -
stainless

What is the total number of hours in the first period Welder Training Profile? - 240

When starting a cut on plate, the preheat cones should be held: - about 3 mm (1/8") above the
surface.

What is the main purpose of the contact tube? - transfers the welding current to the filler wire

A steamed vessel is safest to weld on when it is cooled down to room temperature . - False

Three basic oxy/acetylene flame types are known as: - carbonizing, neutral, oxidizing

Which of the following is a abbreviation of a welding process? - OAW

What current and polarity is used in plasma Arc cutting and gouging operations? - DCEN and
DCRP

"Nesting" in GMAW wire feeder can be caused by: - drive roll pressure is set to high

In the AWS designation ER70T-6, the digit '0' would tell you that: - This is a flat and horizontal
filler metal

Grossly unequal pressure of gases may cause a: - flashback.

What is the definition of sling angle? - the angle formed by the legs to the horizontal plane

Where the rigging was assembled or fabricated by the employer, what percent of the ultimate
breaking strength of the weakest component must the working load not exceed if the rigging is
used to support workers? - 10%

How much electrode stickout is recommended when using gas shielded FCAW with 1.2 mm
(0.045") wire? - 10 mm to 19 mm (3/8" to 3/4")

What type of wire feed set-up is used with CV power sources? - constant speed

What would the recommended regulator pressure be if we were to safely balance a No. 3
welding tip? - 3 lbs. oxygen and 3 lbs. acetylene

Excessive penetration on a root pass would likely be caused by: - travel speeds too low.

The amount of oxygen and acetylene, from cylinders, required to form a neutral cone is: - one
part oxygen, one part acetylene.

The benefits of buying summaries with Stuvia:

Guaranteed quality through customer reviews

Guaranteed quality through customer reviews

Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.

Quick and easy check-out

Quick and easy check-out

You can quickly pay through credit card for the summaries. There is no membership needed.

Focus on what matters

Focus on what matters

Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!

Frequently asked questions

What do I get when I buy this document?

You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.

Satisfaction guarantee: how does it work?

Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.

Who am I buying these notes from?

Stuvia is a marketplace, so you are not buying this document from us, but from seller ACTUALSTUDY. Stuvia facilitates payment to the seller.

Will I be stuck with a subscription?

No, you only buy these notes for £6.46. You're not tied to anything after your purchase.

Can Stuvia be trusted?

4.6 stars on Google & Trustpilot (+1000 reviews)

62890 documents were sold in the last 30 days

Founded in 2010, the go-to place to buy revision notes and other study material for 14 years now

Start selling
£6.46
  • (0)
  Add to cart