ABSA Bundled Exams Questions and Answers 100% Verified and Updated 2024 | Graded A

Power Engineering ABSA 4B Exam Questions and Answers 100% Pass After a bearing has been removed for cleaning, it should be soaked for a period of _____ hours in clean solvent. A) 12 to 16 B) 12 to 14 C) 14 to 16 D) 10 to 12 E) 15 to 16 A- Answer If an oil's viscosity changes a great deal ...

ABSA: 4th Class Part B - Comprehensive Exam 2 Questions and Answers 100% Pass What must be located outside a Class T machinery room? Select one: a. Spare flashlights b. Disposable coveralls c. Machinery shut off switch d. Light switches - Answer- c Degradation of heat transfer fluid of a hot...

ABSA: 4th Class Part B - Comprehensive Exam 1 Questions and Answers 100% Pass Temporary hardness in feedwater is caused by: Select one: a. Magnesium sulphate b. Calcium carbonate c. Magnesium bicarbonate d. Sodium nitrate - Answer- c What is the recommended boiler water pH for wet layup? Se...

ABSA B1 Study Bank Questions with 100% Correct Packaged watertube boilers capacities range from? a. 2300 kg to 65000 kg per hour b. 500 kg to 100 mg per hour c. 15 psi to 15000 kg per hour d. 65000 to 100000 kg per hour - Answer- A The main advantage of the packaged boiler is its a. small siz...

4th Class ABSA Exam Part A Practice Questions and Answers 100% Pass Absolute pressure is: - Answer- gauge pressure plus atmospheric pressure The motion of moving parts is _____ by friction: A: Prevented B: Improved C: controlled D: resisted E: Regulated - Answer- D: resisted Voltage is a) ...

ABSA: 4th Class Part B - Comprehensive Exam 4 Questions and Answers 100% Pass One of the legal responsibilities of the engineer during an inspection is: Select one: a. To notify the Workers Compensation Board of the inspection b. Point out any known or suspected defects to the inspector c. To ...

ABSA Practice 4A – 1 Questions and Answers 100% Pass (4-081-1.16) The output voltage of a shunt DC generator is varied by adjusting the: Select one: a. Pole piece air gaps b. Output current c. EMF d. Field rheostat - Answer- d (4-085-1.11) The Bourdon tube is often shaped in the form of a ...

ABSA 4B Exam Questions and Answers 100% Pass Which of the following pump designs has a spiral casing with an increasing cross sectional area? 1. rotary pump 2. rotary gear pump 3. rotary lobe pump 4. reciprocating pump 5. volute pump - Answer- 5. volute pump A clear line of sight to the flam...

ABSA 4B EXAM QUESTIONS AND ANSWERS 100% PASS Internal ____ is not required for dynamic type compressors. seals lubrication pressure monitoring corrosion monitoring temperature monitoring - Answer- b Low pressure or high pressure are the two primary classifications of ____. centrifugal pumps...

ABSA 3B2 Questions with 100% Correct Answers What can not be used to to control an overspeed trip - Answer- Pneumatic What refrigerants are most commonly used in an absorption refrigeration system - Answer- ammonia and water Where is the flare pit located in an industrial wastewater treatment pl...

ABSA 5th Class Exam Questions and Answers 100% Pass Where are the return openings located regarding air distribution systems? - Answer- Return air openings are located on inner walls. The minimum temperature of the water used in a hydrostatic test of a boiler cannot be less than what temperatur...

ABSA Study Guide22 Questions and Answers 100% Pass Which of the following would be used to dilate a urethral stricture? Choose one Foley Bakes Filiform with followers None of the above - Answer- Filiform with followers Reverse Trendelenburg's position - Answer- The head of the bed is raised...

ABSA 4TH CLASS PART A REVIEW QUESTIONS AND ANSWERS When applying to write a Power Engineer certificate of competency examination, the candidate must: Select one: a. Undergo mandatory drug testing b. Hold the next lower class of qualification c. Pass a criminal records check d. Pass both a wri...