NCCCO Telescopic Boom Crane- Swing Cab(TLL) EXAM PREPARATIONs COMPILATION BUNDLE 100% GUARANTEED SUCCESS

ABC - Articulating Boom Cranes basic crane categories - Fixed or swing. Crawler or truck. Boom or Lattice. BTF - Boom Trucks - Fixed Cab CCO - Certification of Crane Operators clamshell bucket - two snapping turtle hands competent person - Someone who is capable of identifying existing and pred...

The point where you can assume an objects weight to be located is the A. Moment B. Center of gravity C. Tipping axis D. Gross weight - B. Center if gravity If a cranes load chart becomes lost or illegible _____. A. Only the manufacturer can replace it B. The company engineer can recreate it ...

Broken wires in standing line More than 2 in 1 lay beyond end connection ; more than 1 at end connection Broken wires in Rotation resistant 2 wires in 6 rope diameters ; 4 wires in 30 rope diameters Broken wires for running rope 6 random in 1 lay ; 3 in 1 strand in 1 lay When attaching sling t...

TT 345-750V - 16ft TT TA 500-750V - 35ft TA TT 50-345V - 10ft TT TA 750-1000V - 45ft TA TA 50-200V - 15ft TA TA 350-500V - 25ft TA TT ft TT TT .01-.75 - 4ft TT TA 200-350V - 20ft TA TA up to 50V - 10ft TA TT .75-50V - 6ft TT How many electrocution hazard warnings must be displayed - 1 in ...

What is the purpose of installing an auxiliary boom point sheave to the main boom tip? Separate hoist lines A designated Lift Director shall be assigned by the ______? Site Supervisor Who is responsible for calculating net capacity? Crane Operator Who is responsible for ensuring all rigging is...

Which area do truck cranes without a 5th outrigger generally have no lifting capacity unless the manufacturer states otherwise? - The front What is the definition of "operating radius?" - The distance from the center of rotation of the crane to the center of gravity of the load What applies to t...

What action does a signal person intend the operator to perform if he extends his arm at shoulder height, makes a fist with his hand, and sticks his/her thumb up? - Boom up When hoisting personnel, within what percentage of level must a telescopic boom crane be in order for the gross ratings in the...

When should the operator use the "run by the seat of the pants" technique? - Never You are required to pass a physical every ______ years according to ASME B30.5 - 3 Loading radius is the distance from the center of gravity of the suspended load to the: - Center of rotation A stationary load is...

Where is the best location for leveling a crane? - upper works When determining the "gross load" the best method is: - get an accurate load weight and add the rigging By order of hitch strength, which is the correct answer? - basket, vertical, choker What is the purpose of using a jib? - increa...

A crane is operating with a long boom, on outriggers, on uneven ground. Under these conditions it is important to - Block under the float or pad to achieve a 90 degree angle between the cylinder rod and the float or pad What is the purpose of a boom length indicator? - Indicates the extended length...

Which statement best describes the importance Osha 29 CFR 1926.550 places on a crane manufacturers instructions specifications and limitations? - They must be followed exactly as the law According to Osha 29 CFR 1926.550 where must hand signals be placed - On the job site According to Osha 1910.18...

What are some hazards for mobile cranes excavations? - Vibrations from other equipment, previously excavated soils When do you consider the weight of the wire rope to be part of the load for deductions? - Multi part reeve when extra line is not necessary to make the pick You never take the weight ...

An outrigger float should be approximately how much larger that the outrigger pad? 3 times Where should the slings be attached when lifting lattice boom sections? use the end connections When assembling lattice boom sections, which set of pins are installed first? both upper When installing th...

Jib offset is the jib angle to the: - Boom. All hazards and problems that are found on the worksite should be identified: - At the preoperational worksite inspection. What percentage of gross capacity is used when lifting with more than one crane? - 75%. You are required to pass a physical exam e...

What are some hazards for mobile cranes excavations? - Vibrations from other equipment, previously excavated soils When do you consider the weight of the wire rope to be part of the load for deductions? - Multi part reeve when extra line is not necessary to make the pick You never take the weight ...

Crane configuration includes - Reeving, boom length, counterweight, on outriggers, on rubbers, extensions or jibs stowed or mounted, off sets, wire rope type or construction. How does the operator determine the manufacturers recommended rope for the crane - Read the manufacturer load chart or opera...

Jib offset is the jib angle to the: boom All hazards and problems that are found on the worksite should be identified: at the preoperational worksite inspection which of the following OSHA regulations govern suspended personal platform OSHA 1926.1431 3 multiple choice options according to OSH...

Jib offset is the jib angle to the - Boom All hazards and problems that are found on the worksite should be identified: - At the preoperational worksite inspection Which of the following OSHA regulations govern suspended personnel platforms: - OSHA 1926. 1431 According to OSHA 1926.1408 the prohi...