d (very important) - - The ability to utilize all types of communication skills is ____ to the HVACR technician. a. not as important as "hands-on" technical skills b. somewhat important c. unimportant d. very important d (all of the above: clear, complete, concise) - - It is important to be ____ in...
NATE Exam: Core Essentials | 121 Questions
with 100% Correct Answers
d (very important) Correct Answer: The ability to utilize all types of communication skills is
____ to the HVACR technician.
a. not as important as "hands-on" technical skills
b. somewhat important
c. unimportant
d. very important
d (all of the above: clear, complete, concise) Correct Answer: It is important to be ____ in filling
out service orders so that office staff, other technicians, and customers will know what work you
completed on the job.
a. clear
b. complete
c. concise
d. all of the above
d (Refrigerant) Correct Answer: When explaining to a customer that you have adjusted the
system charge, which of the following terms is most appropriate?
a. Freon
b. Gas
c. Juice
d. Refrigerant
a (can help you diagnose the problem) Correct Answer: Listening carefully to what a customer
is telling you ____.
a. can help you diagnose the problem
b. is a waste of time
c. is not necessary
d. often will only confuse you
b (listen to the customer first, then ask questions) Correct Answer: When you arrive at a service
call and meet the customer, you should ____.
a. ask questions first, then listen to what the customer has to say
b. listen to the customer first, then ask questions
c. avoid discussion with the customer
d. remind the customer that you are the professional and get on with your work
,b (1,600 ft3) Correct Answer: What is the volume of a room that measures 10 ft by 20 ft with an
8-ft ceiling?
a. 800 ft3
b. 1,600 ft3
c. 2,400 ft3
d. 3,200 ft3
b (1,200 CFM) Correct Answer: What is the CFM requirements for an 1,800-ft2 house with 8-ft
ceilings, if five air changes per hour are needed?
a. 400 CFM
b. 1,200 CFM
c. 1,600 CFM
d. 2,400 CFM
c (1,600 CFM) Correct Answer: What is the CFM requirement for an 2,400-ft2 house with 8-ft
ceilings, if five air changes per hour are needed?
a. 400 CFM
b. 1,200 CFM
c. 1,600 CFM
d. 2,400 CFM
a (79 in2) Correct Answer: What is the cross-sectional area of a 10-in round metal duct?
a. 79 in2
b. 200 in2
c. 314 in2
d. 418 in2
Note: Area of a circle = π x radius^2
d (1,800 ft/min) Correct Answer: How fast does air with a velocity pressure of 0.20 in. w.g.
move through a round duct?
a. 400 ft/min
b. 1,200 ft/min
c. 1,600 ft/min
d. 1,800 ft/min
Note: Velocity = 4005 x (the square root of velocity pressure)
d (1,800 ft/min) Correct Answer: How fast does air with a velocity pressure of 0.20 in w.g.
move through a square duct?
, a. 400 ft/min
b. 1,200 ft/min
c. 1,600 ft/min
d. 1,800 ft/min
Note: Velocity = 4005 x (the square root of velocity pressure)
d (all of the above: honest, loyal, patient) Correct Answer: Customers depend on you to be ____.
a. honest
b. loyal
c. patient
d. all of the above
c (demonstrate system operation and describe basic maintenance procedures to the customer)
Correct Answer: Before leaving a service call, you should be sure to ____.
a. ask the customer for referrals
b. collect payment in cash if possible
c. demonstrate system operation and describe basic maintenance procedures to the customer
d. try to sell the customer an equipment upgrade
d (All of the above: it can cut hard or soft drawn copper; it leaves no metal shavings to
contaminate the system; it produces a clean, square cut.) Correct Answer: What is the advantage
of using a tube cutter to cut copper pipe?
a. It can cut hard or soft drawn copper
b. It leaves no metal shavings to contaminate the system
c. It produces a clean, square cut
d. All of the above
a (soft drawn copper) Correct Answer: Spring-type benders may be used on ____.
a. soft drawn copper
b. hard drawn copper
c. all copper pipe
d. steel pipe
a (make a mechanical joint in tubing) Correct Answer: A flaring tool is used to ____.
a. make a mechanical joint in tubing
b. measure pipe diameters
c. remove burrs from piping
d. solder tubing without the use of coupling
d (solder tubing without the use of couplings) Correct Answer: A swaging tool is used to ____.
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller Classroom. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $10.99. You're not tied to anything after your purchase.
