NCCER MILLWRIGHT PRACTICE EXAM 2 QUESTIONS & ANSWERS 100% ACCURATE
26 views 1 purchase
Course
NCCER MILLWRIGHT
Institution
NCCER MILLWRIGHT
unusual - ANSWER-If the seal was not properly aligned or there is excessive wear in some bearing or shaft,_______ wear tracks will be the indicator
sharpened brass putty knife - ANSWER-For removing hard to remove gasket materials found on sealing surfaces, ______ is recommended
Conducted on t...
NCCER MILLWRIGHT PRACTICE EXAM
2 QUESTIONS & ANSWERS 100%
ACCURATE
unusual - ANSWER-If the seal was not properly aligned or there is excessive wear in
some bearing or shaft,_______ wear tracks will be the indicator
sharpened brass putty knife - ANSWER-For removing hard to remove gasket materials
found on sealing surfaces, ______ is recommended
Conducted on the job - ANSWER-Apprenticeship training is_______
distance - ANSWER-Charting alignment on a graph requires a chart that is divided into
thousandths of an inch vertically for the indicator readings and into whole inches
horizontally for the__________
hidden - ANSWER-The orthographic drawing may contain a dashed or _______ line
Radiation - ANSWER-In order to shoot through a test object and project an image onto
a detector or a sheet of film, radiography uses a source of penetrating called _______
*scribe circles
*transfer measurements
*compare distances
<measure angles - ANSWER-Which of the following task would you not perform with
dividers?
10% - ANSWER-The over speed trip device is actuated when the turbine reaches a
predetermined limit usually _________% above normal full-load speed
high - ANSWER-Positive results in an offset measurement mean that the MTBM is
_____ or on the 3-o'clock side.
offset misalignment - ANSWER-The coupling gap is set, and then the ______ is
measured
pressure - ANSWER-In a hydraulic system, movement depends on_____
furniture or utility items - ANSWER-Fractional dimensions are used on objects such as
_______ or ______
, elimination - ANSWER-If the cause of the problem is not immediately understood, the
process of________is often the procedure of choice
3/16 - ANSWER-When applying sealant to the sealing gland flanges, keep the sealant
away from the inside edges of the flange by at least_______ inch
Transducer - ANSWER-A stroboscope is triggered by a_______
thread - ANSWER-The pitch of threaded fasteners is measured with a ________gauge
Surface cracks - ANSWER-Liquid penetrant highlights flaws and reveals________
die - ANSWER-A tool used to cut external threats on s bolt or rod is called a ______
special processes - ANSWER-A bill of materials may include info on _______ and other
reference information
surface speed - ANSWER-Engaged gears always have the same _____
general arrangement - ANSWER-Elevation of equipment is usually found in the_____
Vibrations - ANSWER-Inspect the pulleys, rollers, and idlers for unevenness or______
15-20 degree angle - ANSWER-When cutting thin steel with Oxyfuel fuel cutting
equipment, hold the torch so that the tip is pointing in the direction the torch is traveling
at a _____ angle
Grease......... - ANSWER-Labby seals work BEST with materials such as_____
Friction - ANSWER-Lubrication is the application of any substance that
reduces________
Driver coupling jig - ANSWER-When the dial indicator is mounted on the complex
reverse driven coupling jig , the indicator is registered on the____
In racks - ANSWER-Pipe should be stored_____
Single deep groove radial - ANSWER-The most common type of ball bearing is a _____
bearing
split - ANSWER-Couplings that are installed after the driver and driven shafts have
been aligned and the equipment has been fastened into position are ________
couplings
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller IMORA. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $10.19. You're not tied to anything after your purchase.
