Millwright Test Exam Questions With Verified Answers Graded A+ 2024/2025
0 view 0 purchase
Course
Millwright
Institution
Millwright
Millwright Test Exam Questions With Verified Answers Graded A+ 2024/2025
If the seal was not properly aligned or there is excessive wear in some bearing or shaft______ wear tracks will be the indicator.
Unusual
For removing hard to remove gasket materials found on sealing surfaces ______ is ...
millwright test exam questions with verified answe
Written for
Millwright
All documents for this subject (1268)
Seller
Follow
EXAMSMART
Reviews received
Content preview
Millwright Test Exam Questions With Verified
Answers Graded A+ 2024/2025
If the seal was not properly aligned or there is excessive wear in some bearing or shaft______ wear
tracks will be the indicator.
Unusual
For removing hard to remove gasket materials found on sealing surfaces ______ is recommended.
sharpened brass putty knife
Apprenticeship training is
Conducted on the job
Charting alignment on a graph requires a chart that is divided into thousandths of an inch vertically
for the indicator readings and into whole inches horizontally for the _______ measurements.
Distance
The orthographic drawing may contain a dash or ______ line
Hidden
In order to shoot through a test object and project an image onto a detector sheet or film radiography
used as a source of penetrating _____.
Radiation
Which of the following task would you not perform with dividers?
Measure angles
The overspeed trip device is actuated when the turbine reaches a predetermined limit usually
_______ percent above normal full load speed
10
Positive results in an offset measurement mean that the MTBM is ______ or on the 3 o'clock side
High
Coupling gap is set and then there is measured
Offset misalignment
In a hydraulic system movement depends on
Pressure
Fractional dimensions are used on objects ____
Such as furniture or utility items
If the cause of the problem is not immediately understood the process of _____ is often the
procedure of choice
,Elimination
When applying sealant to the sealing glands flanges keep the sealant away from the inside edges of
the flange by at least _______ inch
3/16
A stroboscope is triggered by _______
Transducer
The page of threaded fasteners is measured with a ______ gauge.
Thread
Liquid penetrant highlights flaws in reveals ______.
Surface cracks
The tool used to cut external threads on a boat or rod is a____
Die
A bill of materials may include information on ______ and other reference information
Special processes
Engaged gears always have the same ______
Surface speed
Elevation of equipment is usually found in the
General arrangements
Inspect the police rollers in idlers for unevenness or _____
Vibrations
When cutting then steel with oxy fuel cutting equipment all the torch say that the temp is pointing in
the direction the torch is traveling at a ______ angle
15-20 degrees
Labyrinth seals work best with materials such as
Grease
Lubrication is the application of any substances that reduces _____
Friction
When the dial indicator is mounted on the complex reverse driven coupling jig the indicator is
registered on the ____
Driver coupling Jig
, Pipe should be stored ____
racks
The most common type of ball bearing is a _____ bearing
Single deep groove radial
Couplings that are installed after the driver and driven shafts have been aligned and the equipment
has been fastened into position are _____ couplings
Split
When two or more numbers are multiplied to make another number they are called ______ of the
third number
Factors
The continuous reading dial indicator starts at zero and _____
Increases clockwise
Vibration with an a specific narrowband range can be detected by _____.
Electronic filters
Of the following types of O-rings you would select _______ for an application where temperatures
may be -300°F or 500°F
Teflon
Special cleaning tips for cutting of bald head in notes is called a _______ tip
Rivet cutting
PCVs limit and regulate the _____ in the system
Pressure
The total distance that the chef travels from one piece to the other during one vibration cycle is the
_____.
Displacement
A positive- contact seal generally used on cylinder pistons is the ______ seal
Cup
Equipment reference points are marked with
Brass plugs
On a hydraulic press use a piece of material softer than the work best to keep from ______ the work
piece
Marring
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller EXAMSMART. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $10.39. You're not tied to anything after your purchase.
