NCCER MILLWRIGHT PRACTICE EXAM QUESTIONS & ANSWERS (100% CORRECT)
13 views 0 purchase
Course
NCCER MILLWRIGHT
Institution
NCCER MILLWRIGHT
NCCER MILLWRIGHT PRACTICE EXAM QUESTIONS & ANSWERS (100% CORRECT) unusual - ANSWER-If the seal was not properly aligned or there is excessive wear in
some bearing or shaft,_______ wear tracks will be the indicator
sharpened brass putty knife - ANSWER-For removing hard to remove gasket materials
...
NCCER MILLWRIGHT PRACTICE EXAM 2 QUESTIONS & ANSWERS 100% ACCURATE unusual - ANSWER-If the seal was not properly aligned or there is excessive wear in some bearing or shaft,_______ wear tracks will be the indicator sharpened brass putty knife - ANSWER-For removing hard to remove gasket materials found on sealing surfaces, ______ is recommended Conducted on the job - ANSWER-Apprenticeship training is_______ distance - ANSWER-Charting alignment on a graph requires a chart that is divided into thousandths of an inch vertically for the indicator readings and into whole inches horizontally for the__________ hidden - ANSWER-The orthographic drawing may contain a dashed or _______ line Radiation - ANSWER-In order to shoot through a test object and project an image onto a detector or a sheet of film, radiography uses a source of penetrating called _______ *scribe circles *transfer measurements *compare distances <measure angles - ANSWER-Which of the following task would you not perform with dividers? 10% - ANSWER-The over speed trip device is actuated when the turbine reaches a predetermined limit usually _________% above normal full-load speed high - ANSWER-Positive results in an offset measurement mean that the MTBM is _____ or on the 3-o'clock side. offset misalignment - ANSWER-The coupling gap is set, and then the ______ is measured pressure - ANSWER-In a hydraulic system, movement depends on_____ furniture or utility items - ANSWER-Fractional dimensions are used on objects such as _______ or ______ elimination - ANSWER-If the cause of the problem is not immediately understood, the process of________is often the procedure of choice 3/16 - ANSWER-When applying sealant to the sealing gland flanges, keep the sealant away from the inside edges of the flange by at least_______ inch Transducer - ANSWER-A stroboscope is triggered by a_______ thread - ANSWER-The pitch of threaded fasteners is measured with a ________gauge Surface cracks - ANSWER-Liquid penetrant highlights flaws and reveals________ die - ANSWER-A tool used to cut external threats on s bolt or rod is called a ______ special processes - ANSWER-A bill of materials may include info on _______ and other reference information surface speed - ANSWER-Engaged gears always have the same _____ general arrangement - ANSWER-Elevation of equipment is usually found in the_____ Vibrations - ANSWER-Inspect the pulleys, rollers, and idlers for unevenness or______ 15-20 degree angle - ANSWER-When cutting thin steel with Oxyfuel fuel cutting equipment, hold the torch so that the tip is pointing in the direction the torch is traveling at a _____ angle Grease......... - ANSWER-Labby seals work BEST with materials such as_____ Friction - ANSWER-Lubrication is the application of any substance that reduces________ Driver coupling jig - ANSWER-When the dial indicator is mounted on the complex reverse driven coupling jig , the indicator is registered on the____ In racks - ANSWER-Pipe should be stored_____ Single deep groove radial - ANSWER-The most common type of ball bearing is a _____ bearing split - ANSWER-Couplings that are installed after the driver and driven shafts have been aligned and the equipment has been fastened into position are ________ couplings
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller STUDYLAB2023. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $13.49. You're not tied to anything after your purchase.
