Exam (elaborations)
IPC-A-610 Test Questions and Answers
- Course
- Institution
IPC-A-610 Test Questions and Answers
[Show more]
Content preview
IPC-A-610 Test Questions and Answers3 types of Conformal Coating: Acrylic Resin (AR) - Answer -This type of coating
provides FAIR elasticity and general protection. It has high dielectric strength, and fair
moisture and abrasion resistance. This coating is different from others because its
facility for removal. This type are EASILY and quickly removed by a variety of solvents,
often without requiring agitation. This makes rework and field repair very practical and
economical. This type doesn't protect against solvents and solvent vapors.
3 types of Conformal Coating: Silicone Resin (SR) - Answer -This type of coating
provides EXCELLENT protection in a very wide temperature range. This coating
provides good chemical resistance, moisture, and salt spray resistance, and is very
flexible. This type is NOT abrasion resistant because of its rubbery nature, but this
property does make it resilient against vibrational stresses. Commonly used in high-
humidity environments. Removal can be CHALLENGING. requiring specialized
solvents, long soak time, and agitation from a brush.
3 types of Conformal Coating: Urethane (Polyurethane) Resin (UR) - Answer -This type
of coating is known for its EXCELLENT moisture and chemical resistance. It is also very
abrasion resistant. Combining those factors with its SOLVENT RESISTANCE results in
a conformal coating that is very difficult to remove. Like SR, full removal generally
requires special solvents, long soak time, and agitation with a brush. This is common in
aerospace application. ex: Conathane
5 Coating application methods: Manual Spraying - Answer -Aerosol can or handheld
spray gun. Time consuming method of coating for a small quantity of boards. Lots of
masking beforehand. Quality and consistency of outcome are operator- dependent.
5 Coating application methods: Automated spraying - Answer -Programmed spray
system that moves the board on a CONVEYOR under an alternative spray head that
applies a conformal coating.
5 Coating application methods: Selective coating - Answer -An automated conformal
coating process that uses PROGRAMMABLE ROBOTIC SPRAY NOZZLES to apply
the coating to very specific areas on the circuit board. May eliminate the need for
masking using the program. The UV lamp in machine helps cure the coating right after it
is sprayed.
5 Coating application methods: Dipping - Answer -The circuit board is first immersed,
Then withdrawn from the conformal coating solution. Immersion speed, withdrawn
, speed, Immersion time, and Viscosity determine the resulting film formation. Common
for high volume processing. Masking may increase. This method is good to coat both
Front and Back of the board.
5 Coating application methods: Brushing - Answer -Simple application method used
mainly in repair and rework. Conformal Coating is applied with a BRUSH to specific
areas on the board. Low-cost method but requires lots of manual labor and is highly
variable depending on operator proficiency and consistency. This is the best for a small
batch or a single board.
1. Solvent Removal
2. Peeling
3. Microblasting: using a concentrated mix of soft abrasive and compressed air to
abrade the coating.
4. Grinding/Scaping - Answer -What are the Conformal Coating Removal Methods by
IPC? (4)
(6) Most Common Coating Defects and causes:
Capillary Flow - Answer -occurs when coating migrates from one area of a board to
another, leaving behind an inconsistent, uneven finish on the surface.
Causes: -application of too much coating
- coating with low viscosity or high surface tension.
- low surface energy of component being coated.
(6) Most Common Coating Defects and causes:
Cracking and Ripples - Answer -Visual cracks and creases on components.
Causes: -coating is too thick
- thermal shock
- coating cured too quickly
(6) Most Common Coating Defects and causes:
Dewetting - Answer -Coating will not evenly coat the surface to which its applied.
Causes: - uneven coating application.
- improper mixture of two- part material.
- Residue on coating surface.
- Surface tension and surface energy.
(6) Most Common Coating Defects and causes:
Delamination - Answer -When coating has lifted up and away from the board. This
hinders protection because the area below the coating is left exposed. (Ex:Ripping off
more coating after demasking and pulling off too much coating around the area.
Causes:
-too thick of coating
- coating not adhering to previous coating layer.
-contamination of surface of the board.
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller millyphilip. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $12.49. You're not tied to anything after your purchase.
Can Stuvia be trusted?
4.6 stars on Google & Trustpilot (+1000 reviews)
79271 documents were sold in the last 30 days
Founded in 2010, the go-to place to buy study notes for 14 years now