Exam (elaborations)
ASE G1 Exam Latest Updated
- Course
- Institution
ASE G1 Exam Latest Updated
[Show more]
Content preview
ASE G1 Exam Latest UpdatedCoolant should be tested for - answer-a. Proper color
b b b b b b b b
b. Freezing point (temperature)
b b b
c. Specific gravity
b b
*d. Both b and c
b b b b
Two technicians are discussing a compression test. Technician A says that the engine
b b b b b b b b b b b b
should be cranked over with the pressure gauge installed for "4 puffs." Technician B
b b b b b b b b b b b b b
bsays
that the maximum difference between the highest-reading cylinder and the lowest-
b b b b b b b b b b
reading
cylinder should be 20%. Which technician is correct? - answer-a. Technician A only
b b b b b b b b b b b b
b. Technician B only
b b b
*c. Both Technicians A and B
b b b b b
d. Neither Technician A nor B
b b b b b
Technician A says that oil should be squirted into all of the cylinders before taking a
b b b b b b b b b b b b b b b
compression test. Technician B says that if the compression greatly increases when
b b b b b b b b b b b
bsome oil b
is squirted into the cylinders, it indicates defective or worn piston rings. Which
b b b b b b b b b b b b
btechnician is b
correct? - answer-a. Technician A only
b b b b b
*b. Technician B only
b b b
c. Both Technicians A and B
b b b b b
d. Neither Technician A nor B
b b b b b
During a cylinder leakage (leak-down) test, air is noticed coming out of the oil fill
b b b b b b b b b b b b b b
opening.
b
Technician A says that the oil filter may be clogged. Technician B says that the piston
b b b b b b b b b b b b b b b
rings may be worn or defective. Which technician is correct? - answer-a. Technician A
b b b b b b b b b b b b b b
only
b
*b. Technician B only
b b b
c. Both Technicians A and B
b b b b b
d. Neither Technician A nor B
b b b b b
Leaking antifreeze can be what color? - answer-a. Green
b b b b b b b b
b. Orange
b
c. Red
b
*d. Any of the above
b b b b
, What precautions are needed to be performed to help prevent air from getting trapped
b b b b b b b b b b b b b
bin
the cooling system when replacing coolant? - answer-a. Use the proper antifreeze as
b b b b b b b b b b b b
bspecified
*b. Open bleeder valve(s) during filling
b b b b b
c. Use premixed coolant
b b b
d. Wear protective gloves
b b b
When replacing a water pump, be sure to - answer-a. Torque all fasteners to factory
b b b b b b b b b b b b b b
bspecifications
b. Use a new gasket/ seal
b b b b b
c. Check that the accessory drive belt is properly aligned and adjusted to the proper
b b b b b b b b b b b b b b
tension
*d. All of the above
b b b b
When using a scan tool to retrieve diagnostic trouble codes (DTCs), the technician
b b b b b b b b b b b b
should
b
also - answer-a. Check monitor status
b b b b b
b. Check freeze frame data
b b b b
c. Record any stored DTCs
b b b b
*d. All of the above
b b b b
When replacing an external fuel filter, best practices include - answer-a. Use the same
b b b b b b b b b b b b b
brand as the original as the replacement filter
b b b b b b b b
b. Reuse the filter after cleaning
b b b b b
*c. Relieve fuel system pressure before removing the fuel line connections
b b b b b b b b b b
d. Tighten fasteners as tight as possible
b b b b b b
Before road testing a vehicle to determine if the automatic transmission is performing
b b b b b b b b b b b b
normally, which should be performed? - answer-a. Check for any stored diagnostic
b b b b b b b b b b b
trouble codes
b b
b. Check the fluid level
b b b b
c. Check the fluid condition and color
b b b b b b
*d. All of the above
b b b b
Automatic transmission cooling lines are located - answer-*a. Between the transmission
b b b b b b b b b b
and the radiator
b b b
b. Between the transmission and the rear axle
b b b b b b b
c. Inside the transmission or transaxle
b b b b b
d. Inside the HVAC module
b b b b
Why is a scan tool needed when checking the level of automatic transmission fluid? -
b b b b b b b b b b b b b b
answer-*a. To determine the fluid temperature
b b b b b b
b. To check for any stored diagnostic trouble codes
b b b b b b b b
c. To check which solenoids inside the transmission/transaxle are active.
b b b b b b b b b
d. To determine the fluid capacity
b b b b b
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller Prose1. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $13.49. You're not tied to anything after your purchase.
Can Stuvia be trusted?
4.6 stars on Google & Trustpilot (+1000 reviews)
72841 documents were sold in the last 30 days
Founded in 2010, the go-to place to buy study notes for 14 years now