100% satisfaction guarantee Immediately available after payment Both online and in PDF No strings attached
logo-home
Elevator Mechanic Exam Review Questions with Complete Answers Graded A+ $13.49   Add to cart

Exam (elaborations)

Elevator Mechanic Exam Review Questions with Complete Answers Graded A+

 11 views  0 purchase
  • Course
  • Mechanics NEIEP
  • Institution
  • Mechanics NEIEP

A contractor wants to raise the car speed from 100fpm to 125fpm, it currently has a 12" sheave. What sheave is required? - Answer: Diam=12" 12/4=3" 25fpm=3" 100fpm + 25fpm= 12"+3"= 15" sheave A MOV (Metal Oxide Varistor) burns out. You replace it, but cannot read voltage or resistance. What sh...

[Show more]

Preview 3 out of 22  pages

  • August 14, 2024
  • 22
  • 2024/2025
  • Exam (elaborations)
  • Unknown
  • Mechanics NEIEP
  • Mechanics NEIEP
avatar-seller
YourExamplug
Elevator Mechanic
Exam Review
Questions and
Complete Solutions
Graded A+
Denning [Date] [Course title]

,A contractor wants to raise the car speed from 100fpm to 125fpm, it currently has a 12" sheave. What
sheave is required? - Answer: Diam=12" 12/4=3" 25fpm=3" 100fpm + 25fpm= 12"+3"= 15" sheave



A MOV (Metal Oxide Varistor) burns out. You replace it, but cannot read voltage or resistance. What
should you do? - Answer: Replace it with a larger MOV



On a Ward-Leonard circuit the break is set, but the motor is trying to slip through the break. What is the
issue? - Answer: Suicide Circuit



You have an old DC motor and are adding an SCR drive, what do you do to the interpoles? - Answer:
Leave the interpoles alone. When adding a SCR drive to the generator, the series loop is removed, as are
the 3 resistors. Everything else remains the same



A hydro runs up with no load, but will not run with a full load. What is the issue? - Answer: The relief
valve is set too low



Runby for a 1:1 hits the CWT buffer 4" below the top landing. CWT runby should be set at 18". How
much should the ropes be shortened? - Answer: 22"



You need to work on a freight door retiring cam, you LOTO the main line but there is still power on the
cam. What circuit is still hot? - Answer: Door Operator Disconnect/ Main Line Disconnect



The contractor requests that the vertical center of a Rack and Pinion hoist be moved. How do you do
this? - Answer: Adjust Tie Downs and Wall Ties



Working pressure on a Hydro is 400psi. What is the maximum relief valve setting? - Answer: 400psi x
150%= 600psi



What must be installed on a false car before operation? - Answer: Spring Loaded Safeties.



There is slight arcing between the brush and commutator. What action must be taken? - Answer: None.

Heavy arcing=Light brush pressure. Heavy bush pressure=mechanical wear

, If rigging gear is roped 3:1 and a BEAM CLAMP is used to lift a 6,000lb load. What is the beam capacity? -
Answer: 18,000lbs. Beam capacity is cut in half with use of clamp, when rigging all blocks, rope, and
clamps will be Equal to the lowest load rating



How much resistance is measured over a normally closed switch? - Answer: 1.2ohms. should be zero,
but will never be that low



A car traveling in the hoistway always stops at the same spot and blows a fuse. What causes this? -
Answer: Traveling cable has a cut/exposed wire or a short



How is a class 1 yearly buffer test preformed? - Answer: Car at bottom landing and on inspection, jump
out direction and final limits. With pit clear, run down to compress buffers, buffers should fully extend
within 90 seconds.

5yr: Full load Full speed

CWT: Full speed Empty



How many strain supports are required on a 350ft raceway? - Answer: 4. 1 every 100ft



How is stainless steel drilled out? - Answer: Slow speed and constant pressure



What is the required amount of retainer clips for wedge shackles and what is the spacing? - Answer:
Minimum 2 clips. 1st at a maximum 4x the diameter of the rope

2nd at a maximum 8x the diameter above the 1st clip



A 300ohm resistor burns out, but you don't have another one. How can you make one? - Answer: 2
600ohm resistors in parallel is 300ohms. Resistance is half of highest resistor in parallel circuit.

3 225ohm resistors in parallel is 75ohms.



When cutting laminated panels, which direction should the finish side face? - Answer: Finish side facing
the cutting edge of the tool. Blade will burr the backside

The benefits of buying summaries with Stuvia:

Guaranteed quality through customer reviews

Guaranteed quality through customer reviews

Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.

Quick and easy check-out

Quick and easy check-out

You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.

Focus on what matters

Focus on what matters

Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!

Frequently asked questions

What do I get when I buy this document?

You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.

Satisfaction guarantee: how does it work?

Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.

Who am I buying these notes from?

Stuvia is a marketplace, so you are not buying this document from us, but from seller YourExamplug. Stuvia facilitates payment to the seller.

Will I be stuck with a subscription?

No, you only buy these notes for $13.49. You're not tied to anything after your purchase.

Can Stuvia be trusted?

4.6 stars on Google & Trustpilot (+1000 reviews)

78998 documents were sold in the last 30 days

Founded in 2010, the go-to place to buy study notes for 14 years now

Start selling
$13.49
  • (0)
  Add to cart