Chapter 8-J&B Driver- Operator Questions and Answers 2024

Chapter 8-J&B Driver- Operator Questions and Answers 2024 1. NFPA ______ is the Standard on Fire and Emergency Service Vehicle Operations Training Programs. A. 1002 B. 1451 C. 1564 D. 1901 B. 1451 Page: 208 2. What term describes the evaluation of fire apparatus and its equipment that ensures its safe operation? A. Truck maintenance B. Fire apparatus inspection C. Fire apparatus maintenance D. Maintenance inspection B. Fire apparatus inspection Page: 209 3. NFPA ______ is the Standard for Automotive Fire Apparatus. A. 1002 B. 1041 C. 1564 D. 1901 D. 1901 Page: 210 4. To properly maintain a fire apparatus, the driver/operator should use _____________ procedures and the manufacturer's recommendations as references. A. national B. state C. department D. county C. department Page: 210 5. Personal protective equipment needed to safely perform a fire apparatus inspection includes _____________, ______________, and _____________. A. safety glasses; work gloves; hearing protection B. helmet; turn-out gear; fire gloves C. clipboard; pen; paper D. flashlight; pliers; screwdriver A. safety glasses; work gloves; hearing protection Page: 211 6. The inspection process begins with a(n): A. detailed look around the apparatus. B. thorough review of the manufacturer's recommendations. C. inspection of the fuel and oil levels. D. review of the apparatus inspection form. D. review of the apparatus inspection form. Page: 211 7. What term refers to the document that identifies the results of previous inspections, including who performed the inspections and when? A. Apparatus maintenance form B. Pre-inspection form C. Apparatus inspection form D. Preincident survey C. Apparatus inspection form Page: 211 8. Often, fire apparatus inspections are broken into sections. According to the text, what is the first section that should be completed? A. Brake inspection B. Pump inspection C. Cab interior D. Exterior inspection D. Exterior inspection Page: 214 9. Visually inspecting under the fire apparatus for any fresh oil, coolant, or other fluid leaks, and checking for any damage to the apparatus body are conducted during which section of the fire apparatus inspection? A. Exterior inspection B. Engine compartment C. Brake inspection D. Pump inspection A. Exterior inspection Page: 214 10. Which of the following exterior inspection components is critical for the proper stability of a fire apparatus? A. Shocks B. Tires C. Struts D. Valve stems B. Tires Page: 214 11. Tires should have at least _______ inch of tread depth in every major groove. A. 1/2 B. 1/16 C. 3/32 D. 4/32 D. 4/32 Page: 214 12. Ten degrees of play is equivalent to ____ inches of movement at the rim of a 20-inch steering wheel. A. 2 B. 4 C. 6 D. 8 A. 2 Page: 215 13. The ____________ system keeps a vehicle's axles in place and holds up the fire apparatus and its entire load. A. power steering B. suspension C. deferment D. exhaust B. suspension Page: 215 14. When inspecting the fire apparatus, which fire apparatus section would focus on inspecting the fluid levels, battery charge, cooling system, motor components such as belts, charging system, and drive train elements? A. Exterior inspection B. Engine compartment inspection C. Brake inspection D. Pump inspection B. Engine compartment inspection Page: 216 15. When adding any fluids to a fire apparatus, the driver/operator should be sure: A. adhere to the manufacturer's specifications. B. to use any type of fluid available. C. to use local mechanic recommendations in what type of fuel is used. D. that mixed liquids are used correctly. A. adhere to the manufacturer's specifications. Page: 210 16. An engine should cool for at least ______ minutes before the driver/operator attempts to check the oil level. A. 5 B. 10 C. 15 D. 20 C. 15 Page: 216 17. When checking the coolant level of a fire apparatus, the driver/operator should: A. remove the radiator cap with his or her bare hand. B. pull the dipstick and check for the appropriate level. C. check the coolant level in a manner recommended by the manufacturer. D. check the coolant level by using the temperature gauge inside the vehicle. C. check the coolant level in a manner recommended by the manufacturer. Page: 216 18. Which of the following fluid levels should you check while the engine is running? A. Fuel B. Oil C. Transmission D. Battery water C. Transmission Page: 217