2024 ICC Concrete Test with complete __., __., __., __., __., __.,
solutions. __.,
Depending upon the jurisdiction, the special inspector is required to send
__., __., __., __., __., __., __., __., __., __., __.,
their final reports to the building official and:
__., __., 1. The design __., __., __., __., __., __.,__., __., __., __., __
professional in responsible charge X
., __., __., __., __.,
2. The building official only
__., __., __., __.,
3. The general contractor, stating their work met compliance
__., __., __., __., __., __., __., __.,
4. The architect of record
__., __., __., __.,
Concrete not sufficiently consolidated in an area will produce ___________
__., __., __., __., __., __., __., __., __.,
_____, which could lead to structural failure because of shear and compre
__., __., __., __., __., __., __., __., __., __., __.,
ssive forces Honeycombing
__., __.,__., __.,
Special provisions for cold weather concreting shall be implemented when
__., __., __., __., __., __., __., __., __., __.,
the ambient temperature at the work area falls below
__., __., 40 degrees __., __., __., __., __., __., __.,__., __., __.,
Pipes in concrete should have a minimum concrete cover of ____________
__., __., __., __., __., __., __., __., __., __.,
__________ when exposed to earth or weather. 1. 3/4 inch
__., __., __., __., __., __., __.,__., __., __., __.,
2. 1 inch
__., __.,
3. 1-1/2 inches
__., __.,
4. 3 inches
__., __.,
A mechanical splice must achieve:
__., __., __., __., __.,__., 125% of the grade strength of
__., __., __., __., __., __., __.,
the bar __.,
, After initial curing is complete, sample cylinders should be maintained
__., __., __., __., __., __., __., __., __., __.,
at a temperature between:
__., __., 73.5 +/- 3.5 degrees __., __.,__., __., __., __., __.,
The ties of a cast-in-
__., __., __., __.,
place prestressed concrete beam not exposed to weather or permanently
__., __., __., __., __., __., __., __., __., __.,
cast against earth shall have a minimum concrete cover of:
__., __., 1 inch __., __., __., __., __., __., __., __.,__., __., __.,
An acceptable reinforcing steel support mechanism for a 24-
__., __., __., __., __., __., __., __.,
inch deep footing are:
__., 1. Precast dobie blocks X
__., __., __.,__., __., __., __., __., __.,
2. Large, solid pieces of glass
__., __., __., __., __.,
3. Masonry CMU pieces
__., __., __.,
4. Wooden blocks
__., __.,
All of the following are true except:
__., __., 1. Minimum concrete cover for
__., __., __., __., __.,__., __., __., __., __., __., __.,
bundled bars of any size need not be greater than 2 inches, unless they
__., __., __., __., __., __., __., __., __., __., __., __., __., __.,
are in a member that's permanently cast against earth
__., __., __., __., __., __., __., __.,
2. Specified concrete cover for headed shear stud reinforcement shall not
__., __., __., __., __., __., __., __., __., __., __.,
be less than the cover requirements for the member in which the stud
__., __., __., __., __., __., __., __., __., __., __., __., __.
reinforcement is located
, __., __.,
3. Concrete cover for flexural members, walls, and compression members
__., __., __., __., __., __., __., __., __., __.,
with an effective depth of 8-inches can vary -3/8 of an inch
__., __., __., __., __., __., __., __., __., __., __.,
4. Concrete cover for members in highly corrosive environments will
__., __., __., __., __., __., __., __., __., __.,
typically remain the same as cast against earth
__., __., __., __., __., __., __.,
Bars must be tied in place to avoid displacement during concrete
__., __., __., __., __., __., __., __., __., __., __.,
placement. The following is not acceptable for securing intersections:
__., __., __., __., __., __., __., __., __.,__., __.
1. Annealed tie wire
, __., __., __.,