100% satisfaction guarantee Immediately available after payment Both online and in PDF No strings attached
logo-home
CWB Welding Inspector Level 2 All Modules ( Latest 2024 / 2025 ) Actual Questions and Answers 100% Correct $11.99   Add to cart

Exam (elaborations)

CWB Welding Inspector Level 2 All Modules ( Latest 2024 / 2025 ) Actual Questions and Answers 100% Correct

 7 views  0 purchase
  • Course
  • CWB
  • Institution
  • CWB

CWB Welding Inspector Level 2 All Modules ( Latest 2024 / 2025 ) Actual Questions and Answers 100% Correct

Preview 4 out of 43  pages

  • September 7, 2024
  • 43
  • 2024/2025
  • Exam (elaborations)
  • Questions & answers
  • CWB
  • CWB
avatar-seller
ExamNavigator
CWB Welding Inspector Level 2
All Module


By ExamNavigator

, CWB Welding Inspector Level 2 All Modules

1. What is the term used to describe the following condition of lost corrosionresistance?
"When certain stainless steels are heated between 500-850° C, carbides format the grain
boundaries and cause a local depletion of chromium."

(A) Oxidization
(B) Increased toughness
(C) Solution heat treatment
(D) Sensitization
Answer: (D) Sensitization

Note: Also known as "carbide precipitation" -- Chromium binds to carbides, and"sweats out"
at the grain boundaries

2. On a radiograph, undercut appears as a line.

(A) light
(B) dark
Answer: (B) dark

3. What is the Canadian Standard for safety in welding?
Answer: CSA W117.2

4. What is the typical three-phase input voltage in most Canadian weldingshops?
Answer: 600V

5. True or False: The cable from the workpiece back to the welding machine iscalled the
"ground lead".
Answer: False. The correct term is the "work lead".

6. What is the type of radiation that can damage living cells?
Answer: Ionizing

7. Name two examples of ionizing radiation.
Answer: X-rays and Gamma rays

8. What is the minimum suggested shade for a welding helmet when using5/32 SMAW
electrode at 150 A?
Answer: Shade 10

,9. Approx. how far could spatter travel when welding/cutting from 2.5m high?-
Answer: Possibly up to 6m

10. What is the toxic component contained in some copper alloys?
Answer: Beryllium

11. Which welding process will likely have the highest fume generation rate?

[SMAW / SAW / FCAW]
Answer: FCAW

12. What do the terms TLV and TWA stand for?
Answer: TLV: Threshold limit valueTWA: Time weighted average

13. The action of UV light on oxygen produces which toxic gas?
Answer: Ozone

14. Which common fuel gas has the widest range where it can become flammable when
mixed with air?
Answer: Acetylene

15. What substance should you NEVER apply to a stiff pressure-adjustingscrew on an
oxygen regulator?: Oil or grease

16. What is the maximum gauge pressure that acetylene should be used?(kPa/psi)
Answer: 103 kPa (15 psi)

17. Which toxic gas is produced when welding on surfaces with chlorinatedhydrocarbon
solvents?
Answer: Phosgene gas

18. What is the typical max. OCV of an AC welding machine?
Answer: 80 V

19. In an isometric drawing, the lines (for width, length and depth) are inclinedat an angle of
how many degrees?
Answer: 30°

20. What are the maximum number of views in an orthographic drawing?
Answer: 6

21. What are the two general classes of picture drawings?
Answer: Perspective andIsometric

, 22. What are the 5 basic joints?
Answer:
1) Butt
2) Corner
3) T
4) Lap
5) Edge

23. What are the 5 basic weld types?
Answer:
1) Groove
2) Fillet
3) Plug/Slot
4) Surfacing
5) Edge

24. Plasma cutting torch temp can reach temperatures of
° Celsius.
Answer: 30,000

25. True or False: All plasma arc cutting equipment is operated using DCEN.-
Answer: True

26. True or False: Stainless steel can be readily cut with a normal oxy-fuel gasprocess.
Answer: False

27. What are the two basic methods of plasma torch operation?
Answer: Transferredand Non-Transferred arc

28. In North America, the 3 othographic views most commonly-used are: TOP,FRONT and
Side.

[RIGHT / LEFT]
Answer: LEFT

29. What is the difference between a "weld symbol" and a "welding symbol"?-
Answer: A "weld symbol" indicates the specific kind of weld to be used (ex. fillet), and is
contained inside of "welding symbol".

30. In a welding symbol, is the size of the weld located to the LEFT or RIGHTof the fillet
weld symbol?
Answer: LEFT

The benefits of buying summaries with Stuvia:

Guaranteed quality through customer reviews

Guaranteed quality through customer reviews

Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.

Quick and easy check-out

Quick and easy check-out

You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.

Focus on what matters

Focus on what matters

Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!

Frequently asked questions

What do I get when I buy this document?

You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.

Satisfaction guarantee: how does it work?

Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.

Who am I buying these notes from?

Stuvia is a marketplace, so you are not buying this document from us, but from seller ExamNavigator. Stuvia facilitates payment to the seller.

Will I be stuck with a subscription?

No, you only buy these notes for $11.99. You're not tied to anything after your purchase.

Can Stuvia be trusted?

4.6 stars on Google & Trustpilot (+1000 reviews)

67866 documents were sold in the last 30 days

Founded in 2010, the go-to place to buy study notes for 14 years now

Start selling
$11.99
  • (0)
  Add to cart