Exam (elaborations)
Pipefitter Star Exam-Questions with Correct Answers/ Verified/ Latest (2024/2025)
- Course
- Institution
Pipefitter Star Exam-Questions with Correct Answers/ Verified/ Latest (2024/2025)
[Show more]
Content preview
Pipefitter Star Exam-Questions with Correct Answers/ Verified/Latest (2024/2025)
What causes 90% of all construction injuries and deaths and are used to help OSHA
inspectors improve their effectiveness? - ✔✔Focus Hazards
What is the minimum safe working distance for overhead power lines? - ✔✔10 feet
What is the standard procedure used to safely de-energize equipment on circuits before
they are worked on? - ✔✔Lockout/Tagout
Which of the following is not true about Material Safety Data Sheets? - ✔✔They can be
written in any language
What are the four focus inspections OSHA compliance officers look for? - ✔✔Fall Hazards,
Electrical Hazards, Caught in, Struck by
The sizes of pipe are identified by the measurement called the: - ✔✔Nominal pipe size NPS
Steel pipe is supplied with the following end finish (es): - ✔✔PESC, T & C TBE
(All of the above)
What is a typical type of welded pipe joints? - ✔✔Butt-welded, Socket-welded, Slip-on
Flanged (All of the above)
List the four principle functions of valves. - ✔✔Start/Stop, Regulate/Throttle, Relief, Reduce
Regulating or throttling flow is done with a: - ✔✔Both B and C, (globe and gate valve)
Name the two basic types of check valves. - ✔✔Lift and Swing
,The most common hanger used in piping systems is the: - ✔✔Clevis
Never expose any part of a compressed gas cylinder to temperatures above: - ✔✔125°F
The four types of copper tube joints are soldered, brazed, flared and _____? -
✔✔compression
What is the maximum recommended service temperature when a brazed joint is used? -
✔✔350 degrees F
Poor alignment of tube joints will cause: - ✔✔spacing difference between tubes and fittings
After fittings and tubes are cleaned and fluxed they should be assembled and soldered: -
✔✔as soon as possible
Name three basic hitches which can be used for lifting with a sling - ✔✔Straight, Choker,
Basket
Which hitch can support the most weight? - ✔✔Basket hitch
Why should the angle between the leg of a sling and the load never be less than 30 degrees?
- ✔✔More stress loads are applied on slings.
What is the weakest part of a chain hoist? - ✔✔Lower hook
An oxyacetylene flame has a peak temperature of approximately: - ✔✔6300°F
What is the purpose of slightly opening/cracking a gas cylinder valve before installing a gas
regulator? - ✔✔clear debris
,Why is it important to ensure that no part of the oxygen handling equipment comes in
contact with oil? - ✔✔causes an explosion
What is the constant used to find the travel with a 45 degree offset? - ✔✔1.414
What is the constant used to find the offset or advance with a 45o offset? - ✔✔.707
Add: 5 1/8 + 1 1/4 + 4 ½ = - ✔✔10 7/8
Subtract: 9 5/8 - 6 15/16 = - ✔✔2 11/16
Multiply: 3 1/5 x 1 ¼ x 1 1/3 = - ✔✔5 1/3
Divide: 11 ¼ by 2 ½ = - ✔✔4 1/2
Change the following to architectural measurements 3.96': - ✔✔3' - 11 ½"
MSDS is part of the "right to know" law. - ✔✔t
IDLH is an individual's daily level of hazards - ✔✔f
Inhalation, ingestion, absorption and injection are four routes of entry. - ✔✔t
When voltage is applied to a conductor, free electrons: - ✔✔Are impelled along the
conductor
The magnetic field around a current-carrying wire: - ✔✔Exists at all points along its length
, A lamp has a source of 110 volts and current of 0.9 amps, what is the resistance of the
lamp? - ✔✔122.2 ohms
The device used in circuits to prevent damage from overloads is called a: - ✔✔Fuse
A thermocouple: - ✔✔Generates a small amount of voltage when heated
Sensible heat is defined as: - ✔✔quantity of heat involved to change a substance that can be
measured with a thermometer
Latent heat is defined as: - ✔✔amount of heat required to bring about a change in state in a
substance
Specific heat is defined as: - ✔✔amount of heat in BTU's required to change the
temperature of 1 pound of a substance 1oF.
The pressure at a certain depth below the surface of a liquid: - ✔✔is the same in all
directions
Pressure is: - ✔✔force per unit of area
Work is defined as: - ✔✔force times distance
Name the two main classifications of pump types. - ✔✔Positive Displacement pumps and
Non-Positive Displacement pumps
The violent flashing and collapsing of vapor bubbles in a centrifugal pump is called? -
✔✔Cavitation
What are two kinds of misalignment that must be checked for when installing pumps -
✔✔Parallel and Angular alignment
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller MikeHarris. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $12.49. You're not tied to anything after your purchase.
Can Stuvia be trusted?
4.6 stars on Google & Trustpilot (+1000 reviews)
81113 documents were sold in the last 30 days
Founded in 2010, the go-to place to buy study notes for 14 years now