General Examination for Plumbing #1 Exam Questions with Verified Answers
0 view 0 purchase
Course
Plumbing
Institution
Plumbing
Building sewers shall be tested by completely filling the sewer with water from the ______ - Answer-Lowest to the highest point
Except for plastic piping systems, HOT AND COLD water piping may be tested with ___ - Answer-50 psi air or the working pressure of the water in the systems for at least...
General Examination for Plumbing #1
Exam Questions with Verified Answers
Building sewers shall be tested by completely filling the sewer with water from the
______ - Answer-Lowest to the highest point
Except for plastic piping systems, HOT AND COLD water piping may be tested with ___
- Answer-50 psi air or the working pressure of the water in the systems for at least 15
minutes
The required clearance in front of a 2-inch cleanout is _______ inches. - Answer-18
inches
A stack, as defined in the code, is.... - Answer-The vertical main of soil, waste, or vent
piping that extends one or more stories
Under no circumstances may gas appliance pressure regulators be vented .... -
Answer-...to the gas utilization equipment flue or exhaust system.
"Aboveground schedule 40 PVC and ABS DWV plastic piping installed horizontally shall
be supported at intervals of not to exceed_______ feet. - Answer-4 feet
When sizing a copper fuel-gas piping system that has an inlet pressure of less than 2
psi with a pressure drop of 0.3 inch w.c, the maximum cubic feet per hour of gas flow
allowed through a 5/8 inch OD. ACR tube 75 feet in developed length is ___ - Answer-
27
A Type B-W gas vent shall terminate at least ___ feet in vertical height above the
bottom of the wall furnace. - Answer-12 feet
The maximum horizontal distance of a trap arm is measured from the inner edge of the
vent to the..... - Answer-weir of the trap
The maximum number of lavatories on a 2 inch horizontal waste line is.... - Answer-8
Sleeves shall be provided to protect piping ____ and _______ walls. - Answer-masonry
& concrete walls.
PEX piping one inch and smaller installed horizontally shall be supported at intervals
NOT exceeding how many inches? - Answer-32 inches
The minimum common horizontal waste pipe serving a bathtub, a lavatory, and a
kitchen sink shall be AT LEAST how many inches? - Answer-2 inches
, The required clearance in front of a 3 inch CLEANOUT is how many inches? - Answer-
24 inches
A refrigerator used to store food and that requires drainage shall be drained by means
of...... - Answer-indirect waste pipe
Sheet metal, constituting a part of any vent connector, shall be at least how many
inches. - Answer-0.0304
One material NOT approved for the installation of an external trap for a urinal is.... -
Answer-drawn-copper, alloy tubing traps
Hub and spigot cast-iron piping in 10-foot lengths, installed horizontally, shall be
supported at intervals of not more than ___ feet. - Answer-10 feet
A drain connecting the compartments of a set of fixture to a trap is called a (an) -
Answer-continuous waste
A device to prevent back flow into the potable water system is called a....... - Answer-
backflow preventer
Copper tube and fittings for drainage and vent piping installed above ground shall be at
least ________ - Answer-Type DWV
A ____ shall be permitted to be installed with indirect waste. - Answer-drinking fountain
Vitrified clay pipe and fitting are _____. - Answer-approved for use as a building drain
and shall be kept NOT less than 12 inches below ground.
Cast-iron soil pipe shall NOT be - Answer-threaded
All trenches deeper than the footing of any building or structure and paralleling the
same must be at least _____ from the bottom exterior edge of the footing or as
approved. - Answer-45 degrees
Sewer or other drainage piping that shall not be installed under or within 2 feet of any
building or structure is..... - Answer-SDR 35 sewer pipe
Cast-iron soil pipe shall be supported at.... - Answer-their base and each floor
Water service pipes, or any other underground pipes, shall NOT be run or laid in the
same trench with ______ unless specific conditions are met. - Answer-SDR 35 sewer
piping
Notifications for inspections of work authorized by the permit shall be made - Answer-
NOT LESS than 24 hrs BEFOREEE the work has to be inspected
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller lectknancy. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $12.49. You're not tied to anything after your purchase.
