Exam (elaborations)
CSA W47.1 AND CSA W59 EXAM QUESTIONS
- Course
- Institution
CSA W47.1 AND CSA W59 EXAM QUESTIONS
[Show more]
Content preview
CSA W47.1 AND CSA W59 EXAM QUESTIONSCSA Standard W59 covers the welding requirements for what type of steel
construction? - Answers-The welding requirements of CSA Standard W59 can be
applied to carbon and low-alloy welded steel
What types of structures are covered in CSA Standard W59? - Answers-CSA Standard
W59 covers statically- and cyclically-loaded (repetitive loading) structures.
What is a low-hydrogen electrode? - Answers-A low-hydrogen electrode is an electrode
that deposits weld metal with a specified maximum limit of diffusible hydrogen.
What are the requirements for contractor certification? - Answers-When mandated in
the contract or in the governing design Standard*, all Contractors performing work
under this Standard must be certified to CSA W47.1 for welded fabrications.
The requirements for welding symbols are specified in what standard? - Answers-
Welding symbols shall be as shown in AWS Standard A2.4, together with the additional
conventions developed for CSA Standard W59 and shown in Annex D of CSA Standard
W59.
What information should be given on a design drawing? - Answers-A design drawing
should contain:
information for preparation of detail and erection drawings;
the effective throat thickness shall be defined, if there are partial penetration groove
welds.
What typical welding information would you expect to find on an erection or detail
drawing? - Answers-A) location, type, size and length of all welds:
B) distinguish between shop and field welds;
C) groove depths and joint preparations, if there are partial penetration joints,together
with the position of welding;
D) any notes required, e.g. welding sequence, control of distortion, etc..
What are the types of welds as specified in CSA Standard W59? - Answers-Welds are
classified as groove, fillet, plug or slot welds.
What is a complete joint penetration (CJP) groove weld? - Answers-A CJP groove weld
is one that has complete penetration and fusion of weld and
base metal throughout the thickness of the joint.
What is a partial joint penetration groove weld? - Answers-A partial joint penetration
groove weld is defined as one having
joint penetration less than complete
, Does CSA Standard W59 allow for the use of intermittent groove welds? - Answers-No.
Groove welds must be continuous for the full length of the joint or as otherwise
permitted by the Engineer.
The Term Bureau Means: - Answers-Canadian Welding Bureau
In this standard the term contractor means: - Answers-Fabricator or Erector
Welding terminology shall be defined as: - Answers-AWS Standard A3.0
Preheat required for a CAN3-G40.21m 350W Steel, 20mm thick, at an ambient
temperature of -5°C, using E48018 electrode - Answers-10°C
The maximum gap permissible after assembly of a butt joint to be groove welded, with
steel backing bar, and with a root opening of 6 mm: - Answers-12mm
The largest size notch in a flare cut edge that the fabricator can remove by grinding
without approval is: - Answers-5mm
A 6 mm fillet weld, the actual minimum size must be deposited if the gap between par is
0.8 mm: - Answers-6mm
What welding processes are covered in CSA Standard W59? - Answers-This standard
covers the SMAW, GMAW, GTAW, MCAW, FCAW, SAW, ESW, EGW and SW
processes.
Does CSA Standard W59 specify requirements for stud welding? - Answers-Yes,
Clause 6 has requirements for stud welding.
Does CSA Standard W59 contain provisions for pre-qualified joints? - Answers-Yes,
Clause 10 has details for the geometry of joints that are prequalified, provided
the welding procedures
What base metals can be welded under CSA Standard W59? - Answers-Welding
Supervisor - the company's designated person(s)
directly responsible for ensuring that qualified tack welders, welders, and welding
operators weld in accordance with approved or accepted welding procedure data sheets
in the shop and the field
Which type of weld is prohibited for dynamically loaded structures: - Answers-Slot Weld
For the purpose of CSA W59 standard, welds shall be classified as: - Answers-all of the
above (Plug, Fillet, Groove).
SAW fillet welds made in flat or horizontal position, except single pass fillet welds made
in
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller GEEKA. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $9.99. You're not tied to anything after your purchase.
Can Stuvia be trusted?
4.6 stars on Google & Trustpilot (+1000 reviews)
79373 documents were sold in the last 30 days
Founded in 2010, the go-to place to buy study notes for 14 years now