100% satisfaction guarantee Immediately available after payment Both online and in PDF No strings attached
Previously searched by you
INSTRUMENT TECH NCCER EXAM YEAR 2024/2025 / ACCURATE CURRENTLY TESTING EXAM VERSIONS WITH ACTUAL QUESTIONS AND DETAILED ANSWERS WITH A STUDY GUIDE / EXPERT VERIFIED FOR GURANTEED PASS/ LATEST UPDATE.$24.49
Add to cart
INSTRUMENT TECH NCCER EXAM YEAR 2024/2025 / ACCURATE CURRENTLY TESTING EXAM VERSIONS WITH ACTUAL QUESTIONS AND DETAILED ANSWERS WITH A STUDY GUIDE / EXPERT VERIFIED FOR GURANTEED PASS/ LATEST UPDATE.
0 view 0 purchase
Course
INSTRUMENT TECH NCCER
Institution
INSTRUMENT TECH NCCER
INSTRUMENT TECH NCCER EXAM YEAR 2024/2025 /
ACCURATE CURRENTLY TESTING EXAM VERSIONS WITH
ACTUAL QUESTIONS AND DETAILED ANSWERS WITH A
STUDY GUIDE / EXPERT VERIFIED FOR GURANTEED PASS/
LATEST UPDATE.INSTRUMENT TECH NCCER EXAM YEAR 2024/2025 /
ACCURATE CURRENTLY TESTING EXAM VERSIONS WITH ...
INSTRUMENT TECH NCCER EXAM YEAR 2024/2025 /
ACCURATE CURRENTLY TESTING EXAM VERSIONS WITH
ACTUAL QUESTIONS AND DETAILED ANSWERS WITH A
STUDY GUIDE / EXPERT VERIFIED FOR GURANTEED PASS/
LATEST UPDATE.
A pressure piping code is found in :
A. ANSI B 31.1
B. NEC 690 .
C. OSHA1910 .
D. ISA S 5.1 - CORRECT ANSWER A. ANSI B 31.1
7) When marking tubing for cutting , the preferred method is
A. Scribe a mark into the tube with a sharp object .
B. Mark the tube with a grease pencil
C. Mark the tube with a felt tip pen
D. Mark the tube with a crayon - CORRECT ANSWER C. Mark the tube with a felt tip pen
8) An example of direct measurement indicator is a :
A. Pressure gauge
B. Bulb thermometer
C. Sight glass
D. Flowmeter - CORRECT ANSWER C. Sight glass
9) On the image , how many hand valves are installed on Tank 1201C
A. 1
B. 2
C. 3
,D. 4 - CORRECT ANSWER C. 3
10) What is the first step in troubleshooting a problem in a system ?
A. Turn off power to the instrument
B. Stimulate an input
C. Verify that there is a problem
D. Stimulate an output - CORRECT ANSWER C. Verify that there is a problem
11) Where can the appropriate elevation of an instrument be found ?
A. Location drawing
B. P & ID
C. Flow diagram
D. Loop drawing - CORRECT ANSWER A. Location drawing
12) Chemical cleaning of tubing attached to instruments may cause damage to sensor
A. Electronics
B. Paint
C. Elements
D. Bolts - CORRECT ANSWER C. Elements
13) When making 90 - degree tubing bend , allowance for springback should be : A. 6 to 8
degrees
B. 4-5 degrees
C. 1 to 3 degrees
D. 0 degrees - CORRECT ANSWER C. 1 to 3 degrees
14) Cable shields should be connected to the :
A. Signal ground reference point
B. Ground at each accessible location
,C. First accessible grounding electrode
D. Raceway or cable tray in which the cable is routed - CORRECT ANSWER B. Ground at each
accessible location
15) An employee de energizes a piece of equipment by removing the power plug from the outlet
. If the employee continues to hold on to the power plug once removed , this employee is said to
have what type of control over the energy potential ?
A. Isolation control
B. Lockout tagout
C. Exclusive control
D. Remote control - CORRECT ANSWER C. Exclusive control
16) A compressor keeps blowing a PSV for troubleshooting a technician should start looking at
A. Power switch setting
B. Pressure switch deadband
C. Level switch setting
D. Float swich deadband - CORRECT ANSWER B. Pressure switch deadband
17) In the figure provided the pipe line that carries working process fluid such as steam water or
gas is labeled as
A. A
B. B
C. C
D. D - CORRECT ANSWER A. A
18) A heat reactive dryer is producing damp instrument air what could be a simple fix
A. Replace desiccant
B. Change to a different desiccant
C. Adjust the cycle time
D. Add a second set of dryers - CORRECT ANSWER C. Adjust the cycle time
, 19) Type J thermocouple extension wire is
A. White & red
B. Yellow & red
C. Blue & red
D. Green & red - CORRECT ANSWER A. White & red
20) Which of the following gases should be used to purge tubing and pipe after cleaning
A. argon
B. Air
C. Nitrogen
D. helium - CORRECT ANSWER C. Nitrogen
21) When pressure testing , the required documentation includes :
A. Specification sheets
B. Troubleshooting flow charts
C. Temperature , pressure , and test medium
D. Required corrective measures - CORRECT ANSWER C. Temperature , pressure , and test
medium
22)An air - to - open valve uses
a : A. Fail - in - position actuator
B. Spring - to - open actuator
C. Dual spring actuator
D. Spring - to - close actuator - CORRECT ANSWER D. Spring-to-close Actuator
23) The MOST common method used to measure the flow of liquid in a pipe is to introduce a
restriction in the pipe and measure the :
A. Velocity
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller DrMedinaReed. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $24.49. You're not tied to anything after your purchase.