Exam (elaborations)
HVAC Electrical 19 And 20 Questions And Answers With Verified Solutions Already Passed!!!
- Course
- Institution
HVAC Electrical 19 And 20 Questions And Answers With Verified Solutions Already Passed!!!
[Show more]
Content preview
HVAC Electrical 19 And 20 QuestionsAnd Answers With Verified Solutions
Already Passed!!!
1. A common practice in condensing units is to use a contactor with only one set of
contacts opening only one side of the power to the unit. This is to __. -
ANSWER✔✔ Provide off-cycle heat to the compressor
2. Besides maintaining pressure on the contacts for current carrying capacity, the
pressure springs have a second important function. This is to __. - ANSWER✔✔
Help obtain equal contact against the stationary contacts
3. When a contactor's coil is energized, how much resistance should be measured
between terminal "L1" and terminal "T1"? - ANSWER✔✔ Zero ohms
4. Technician "A" says that if you take a voltage reading from terminal "L1" to
terminal "T1" on a contactor whose coil is energize, you should read zero volts.
Technician "B" says that contactors can only have normally open contacts. Which
of the following statements is correct? - ANSWER✔✔ Technician "A" is correct.
Technician "B" is incorrect
5. An inherent motor protector is a __. - ANSWER✔✔ Thermally activated device
in the motor winding
6. The service factor of an electric motor is determined by __. - ANSWER✔✔
Motor's reserve capacity
7. Standards for motor overload protection are set by the __. - ANSWER✔✔
National Electrical Code
8. A solder pot is part of a __. - ANSWER✔✔ Resettable circuit breaker
9. Which of the following overload devices is not affected by ambient
temperature? - ANSWER✔✔ Magnetic
10. Most electrical problems with an electric motor are __. - ANSWER✔✔ Short
circuited windings, open windings and grounded windings.
, 11. A technician needs to check a single-phase compressor. He labels the three
terminals A, B and C and takes resistance readings of the windings. He reads 10
ohms from A to B, infinity from B to C and infinity form C to A. Identify the
terminals. - ANSWER✔✔ Cannot identify terminals: open windings
12. Technician "A" says that while checking the windings of a compressor, a
reading of 10 ohms or less from the common terminal to ground indicates that the
motor is okay. Technician "B" says that the resistance of the start winding should
always be less than the resistance of the run winding. Which of the following
statements is correct? - ANSWER✔✔ Technician "A" is incorrect. Technician "B"
is incorrect.
13. An open winding in an electric motor means that __. - ANSWER✔✔ A wire in
a winding is broken
14. Technician "A" says that a shorted winding will result in an increased current
flow through the winding. Technician "B" says that if a motor is to be replaced, a
motor with a lower horsepower rating should always be used. Which of the
following statements is correct? - ANSWER✔✔ Technician "A" is correct.
Technician "B" is incorrect
15. If the resistance of the run winding decreases the __. - ANSWER✔✔ Motor
will draw too much current while it is running
16. If a condenser fan motor ground out. It will usually __. - ANSWER✔✔ Trip a
circuit breaker to shut off the unit
17. A megger __. - ANSWER✔✔ Measures very high resistances
18. If a motor hums but does not start, there is a potential problem __. -
ANSWER✔✔ With the starting components, with an open winding, with
insufficient supply voltage.
19. The recommended way to discharge a capacitor is to __. - ANSWER✔✔ Use a
20,000-ohm 5-watt resistor that has insulated leads soldered to it
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller classhub. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $13.49. You're not tied to anything after your purchase.
Can Stuvia be trusted?
4.6 stars on Google & Trustpilot (+1000 reviews)
50843 documents were sold in the last 30 days
Founded in 2010, the go-to place to buy study notes for 14 years now