Nate gas furnace service - Study guides, Class notes & Summaries

HVAC NATE Heat Pump Exam Questions With Correct Answers Updated 2024/2025 (Graded A+) What is the primary purpose of using flux when soldering copper or brass parts? -Ans Prevent Oxidation The water that results from a defrost cycle of an air to air heat pump(runoff) must? -Ans Drain off and away from the outdoor coil. Why must the runoff be drained off and away from the outdoor coil? -AnsExcessive ice can build up on the bottom of the coil and can reduce capacity. What is the component th...

NATE Light Commercial Exam Questions with Correct Answers Graded A+ Which of the following measurements would be needed to determine oil furnace combustion efficiency? a. net stack temperature and CO2 concentration b. net stack temperature and CO concentration c. stack temperature and indoor temperature d. stack temperature and fuel pressure -Ans a. net stack temperature and CO2 concentration When combustion is being tested on an oil furnace, high level of smoke and can be corrected ...

HVAC NATE Heat Pump Exam Questions With Correct Answers Updated 2024/2025 (Graded A+) What is the primary purpose of using flux when soldering copper or brass parts? -Ans Prevent Oxidation The water that results from a defrost cycle of an air to air heat pump(runoff) must? -Ans Drain off and away from the outdoor coil. Why must the runoff be drained off and away from the outdoor coil? -AnsExcessive ice can build up on the bottom of the coil and can reduce capacity. What is the component th...

NATE A/C Exam 1 Low airflow over a residential split system air conditioning evaporator can cause A: Liquid flood-back to the compressor B: A decrease in compression ratio C: An increase in suction line superheat D: Oil logging in the evaporator - Answer-A: Liquid flood-back to the compressor Which of the following is the correct sequence of work? A: Attach gauge manifold, recover refrigerant, replace filter core, evacuate the system, recharge the system. B: Recover refrigerant, evacuat...

NATE Gas Heat Practice Guide 100% accurate, latest updated What precautions are required when mounting any gas furnace on a wood platform in an attic? None The gas control valve may be damaged if exposed to an inlet pressure above what? 14 inch W.C. How many elbows and joints should a vent connector have? As few as possible to reduce resistance of flue gases. Under what conditions, if any may the technician route the exhaust of the furnace into the exhaust vent of the wa...

NATE Core (2022/2023) with Certified Solutions Class A Ordinary Extinguisher Class B Liquid Extinguisher Class C Electrical Extinguisher Asphyxiation causes what? Nausea, Dizziness, Heart Irregularities, and Unconciousness Ladder must be at what dimensions in relation to a house? 4 ft for every 1 ft, 3 ft above the top of the roof. What different amounts does Copper Tubing come in? 25, 50, 100 Soft drawn copper tubing means what? Copper tubing that is on a roll Hard drawn copper tubing me...

NATE Final Exam #2, question and answers with rated solutions A condensing unit should be mounted on a slab that is level to: A: Allow any accumulated water to evenly run out of the cabinet B: Increase airflow through the fin area C: Prevent the unit from tipping over D: Make certain any top discharge air blows straight up A A simple time-activated switch is an example of a control that does not use: A: Feedback B: Electronics C: Calibration D: Manual adjustment ...

NATE A/C Exam #1,100% accurate answers| latest updated Low airflow over a residential split system air conditioning evaporator can cause A: Liquid flood-back to the compressor B: A decrease in compression ratio C: An increase in suction line superheat D: Oil logging in the evaporator A: Liquid flood-back to the compressor Which of the following is the correct sequence of work? A: Attach gauge manifold, recover refrigerant, replace filter core, evacuate the system, recharg...

HVAC NATE Heat Pump, questions and answers with complete top solutions On an R-22 system, line diameters and lengths are typically specified for a vapor pressure drop that does not exceed what? 6-7PSI or 6F What is the primary purpose of using flux when soldering copper or brass parts? Prevent Oxidation The water that results from a defrost cycle of an air to air heat pump(runoff) must? Drain off and away from the outdoor coil. Why must the runoff be drained off and away...