Asme section 9 - Study guides, Class notes & Summaries

Code to follow when performing an internal inspection on pipe - "API 510" Positive material identification (PMI) - "API 578" Fitness for service - "API 579" Risked based inspection (RBI) - "API 580" Valve inspection and testing - "API 598" Cathodic protection - "API 651" Welding on in-service equipment containing the flammables - "API 2201" NDE procedure guidelines - "ASME SECTION V" Design code for fabrication of piping relief devices - "ASME SECTION 8" Welder and wel...

1. Where should a license or temporary permit be located during time of operation of equipment:  Shall be carried ON the person at all times; in the case of a temporary permit the person shall also carry their drivers license 2. Whats the fine for violating section 53, 53a or 54:  No less than $500 and no more than $3,000, or by imprisonment of no more than 3 months, or both fine and imprisonment 3. Whats the fine for permitting an unlicensed person to operate machinery: ...

VT TEST 1 Question and answers 100% correct 2023 50 fc to 100 fc - correct answer What is the range of lighting requirements between the various codes? SNT-TC-1A - correct answer personnel can be certified in accordance to which of the following? 9 - correct answer Which ASME section V article covers visual inspection? 30 degrees - correct answer the inspectors eyes should never be less than __________ to the viewing service direct and indirect - correct answer Whic...

API 570 Open Book Exam Questions and Answers 100% Pass A hydrotest is being conducted on an underground line as a substitute for the external inspection. The test pressure is 200 psig. At the end of the test, the pressure must be at least: - Answer- C.190 psig 2- Determine the maximum allowed pressure for a class 300 flange that has a design temperature of 950 degrees F. The flange material is ASTM A217 gr.C12 - Answer- B. 375 psig 3- An 8 NPS pipe is being replaced with A106 gr. B mater...

NEIEP 200 Final Exam (courses 205- 250): Questions & Answers NEIEP 200 Final Exam (courses 205- 250): Questions & Answers you are about to loosen a fishplate bolt. which wrench would be least likely to slip? (Ansa. 6 point box end wrench b. 12 point box end wrench c. open end wrench you are using a plumb line to check a rail for plumb. you find that at the top it measures 1" and at the bottom it measures 1 1/4". what does this tell you? (Ansa. the top of the rail needs to go towards...

NEIEP 200 Final Exam (courses 205- 250): Questions & Answers NEIEP 200 Final Exam (courses 205- 250): Questions & Answers you are about to loosen a fishplate bolt. which wrench would be least likely to slip? (Ansa. 6 point box end wrench b. 12 point box end wrench c. open end wrench you are using a plumb line to check a rail for plumb. you find that at the top it measures 1" and at the bottom it measures 1 1/4". what does this tell you? (Ansa. the top of the rail needs to go towards...

ASNT VT Level II Exam QUESTIONS AND ANSWERS WITH COMPLETE SOLUTION 2023 B. - 1. Per ASNT Section XI, NDE personnel shall be recertified: A. every 5 years by re-examination B. every 3 years by retraining and retesting C. every 3 years based on continuing satisfactory performance D. annually by retraining B. - 2. Per SNT-TC-1A, when an employee leaves his employer: A. his certification automatically transfers to his new employer B. his certification is automatically terminated...

1. What action does a signal person intend the operator to perform if he extends his arm at shoulder height, makes a fist with his hand, and sticks his/her thumb up? a. Boom down b. Swing c. Boom up d. Extend boom c. 2. When hoisting personnel, within what percentage of level must a telescopic boom crane be in order for the gross ratings in the load chart to remain valid? a. 1% b. 2% c. 5% d. 8% a. 3. The load line of the crane you're operating contacts an energized powe...

API 571 PRACTICE QUESTIONS FOR API 570 EXAM What does "L" mean in Austentic SS, like 304L? A) Has a low carbon content B) has a low chrome content C) has a low nickel level D) has a low toughness level E) is lousy steel A What does "H" mean in Austenitic SS, like 316 H? A) Has a high carbon content B) has a high chrome content C) has a high nickel level D) has a high toughness level E) is horrible steel A Which of the following is NOT a Ferritic Steel? A) 300 Series SS B) ...

ASNT VT Level II Exam (General Questions) With Complete Answers Graded A+ B. every 3 years by retraining and retesting 1. Per ASNT Section XI, NDE personnel shall be recertified:A. every 5 years by re-examination B. every 3 years by retraining and retesting C. every 3 years based on continuing satisfactory performance D. annually by retraining B. his certification is automatically terminated 2. Per SNT-TC-1A, when an employee leaves his employer:A. his certification automatically transf...