Which is not nec - Study guides, Class notes & Summaries

When testing a water level supervisory switch serving a pressure tank a signal shall indicate if the water level _____________from the required level (NFPA 72, Table 14.4.3.2 17 (j) (4) - rises or falls over 3 inches If combination audible/visible appliances are installed the location of the installed appliance shall be determined by the requirements of _______. (Nfpa 72 18.4.8.1) - the visible appliance What is the maximum number of 12 gauge THHN wires that can be installed in 1...

Level 1 Module 10 Basic Electrical Construction Drawings Exam 2023 with complete solution A cutaway view of a building or object is known as a(n)______. Sectional drawing What is the total connected load of Circuit A-1 if each of the Type C lighting fixtures in the figure above has a total lamp and ballast load of 150VA? 1,200VA In which division of the MasterFormat is electronic safety covered? Division 28 A section line on a drawing shows The location of the section on the plan On e...

Any connector with a FOCIS standards document correct answers Which fiber optic connector may be used according to the EIA/TIA 568 cabling standard? The Performance level of unshielded twisted pair cable correct answers What UTP Cat 3, Cat 5e, and Cat 6 or Class D, E, and F rating indicate? 66 Punchdown blocks correct answers Commerical phone systems (not VoIP but POTS) traditionally use multipair UTP cables for backbone connections with _running_____used in the telecom closet for connecti...

IMSA Traffic Signal Technician Level 1| Questions and Verified Answers| Grade A| 100% Correct (2024/ 2025 Update) Q: Hazardous underground utilities: Works must be aware of what ? Answer: Of the location of utilities that cannot be readily seen, including what type they are and the potential for danger that they possess. Q: Most states and provinces have established what ? Answer: Utility protection laws that require contractors to notify all known utility owners prior to ...

Which of these is the symbol used for a 4-way switch? - Answer-c.$4 Lighted handle toggle switches utilize a neon lamp that is illuminated when the switch is in the ___ position. - Answer-b.OFF The ungrounded conductor is often called the ___. - Answer-hot Drawing ___ in Figure 112.415 is a framed locking (not key-lock) type switch. - Answer-Not D.VI or E.None of these To convert a conventional duplex receptacle into a split-wired receptacle, the ___ is removed. - Answer-tab Refer...

NEC TEST ACTUAL EXAM 2024 / NATIONAL ELECTRICAL CODE – NEC TEST ACTUAL 100 QUESTIONS AND 100% CORRECT ANSWERS GRADED A/ NEC / NFPA 70 TEST FOR SAFE INSTALLATION OF ELECTRICAL WIRING AND EQUIPMENT PASSED (NEW!!) Which NEC Article that covers the installation of wiring and equipment for fire alarm systems? - ANSWER-760 The NEC ____ permit the cord and plug connection from a range to a receptacle to be used as the disconnecting means. Does/does not - ANSWER-Does When class 2 control ...

ICD-10-CM Latest Update Graded A+ S02.65XA *3-7 Characters:* 1st Character: Always alpha (A-Z, except U) 2nd Character: Always numeric 3rd-7th Character: Alpha or numeric *First 3 Characters:* Category *4th-6th Characters:* Describe etiology, anatomic site, severity, and such. *7th Character:* Added information for obstetrics, injuries, external causes of injury, and such. X *ICD-10-CM utilizes a placeholder which is always the letter X and has two uses:* 1. As the fifth char...

The Associate CET Study Guide Questions and Answers Rated A+ B+, or supply voltages in electronics products, is considered to be: A. +5 to +12 VDC B. 0 to 30 V DC C. +12 to 300 V DC D. The anode or plate voltage supply D. The anode or plate voltage supply Leakage current in an electronic product, between either of the AC power cord conductors and the chassis or any exposed metals should not exceed _________. A. 5 microamps B. 500 microamps C. 5 milliamps D. 50 milliamps B...

The unit of measurement for resistance is represented by the letter or symbol _________. - Answer-Ohms Voltage is represented by the letter or symbol ________. - Answer-E Current is represented by the letter or symbol _______. - Answer-I Power is represented by the letter or symbol _______. - Answer-P Opposition to current flow is generally termed __________. - Answer-resistance Article _______ in the NEC distinguishes between an outlet and a receptacle. - Answer-100 It is safe...

NCCER 26208-17 Questions and Answers Already Graded A To properly install heat-shrink insulators, _____. Slip the insulator over the connector and apply heat for a few seconds When used in control cable, which of the following must be grounded in order to be effective? Drain wires To determine the correct connector size for MC cable, _____. Refer to the manufacturer literature Burnishes, nicks, and scrapes are generally the result of which of the following? Poorly stripped conductors When st...