Condensing log - Study guides, Class notes & Summaries

Z-51 Written Exam Questions and Complete Solutions In a steam turbine, what is the function of a Kingsbury thrust bearing? A) Maintain first stage steam pressure. B) Compensate for coupling misalignment. C) Adjust shaft torque at start up. D) Maintain axial positioning of the rotor shaft. - Answer: D) Maintain axial positioning of the rotor shaft. The ratio of actual pressure of water pressure in the atmosphere to the saturated pressure of given temperature is A) partial pressure....

Navy Aviation Machinist Mate A School Week Exam Answered perfectly What NSTM deals with propulsion and SSTG Turbines? - NSTM 231 Whats type of rotary pump is frequently used as a lubricanting pump on pumpe and other aux equipment? - Simple gear pimp What is the normal length of a tapered plug? - 3" What is installed on a non-condensing turbone to protect turbine casing from excessive pressure? - Combination exhaust relief valve 2-3 psi above exhaust line pressure On an SSTG, what...

Good telephone etiquette - Answer- a skill every emergency service agency must master Customer service - Answer- Every caller, whether emergency or non-emergency, must be viewed as a customer Decreased customer satisfaction - Answer- means increased complaints and negative results for all. Telephone etiquette - Answer- Your voice reflects your attitude and your attitude will affect the caller. Courtesy helps you control the conversation How do yo gain cooperation and trust - Answer- ...

A carver should be adapted at a __________ to the surface being carved. A. 45 degree angle B. 30 degree angle C. 60 degree angle D. 90 degree angle - Answer- D. 90 degree angle What is the function of the index finger in the modified pen grasp? A. Rest lightly in the side of the instrument B. Holds the instrument handle opposite the thumb C. It has no function in the grasp D. Rests on the incisal or occlusal surface during activation if the instrument - Answer- B. Holds the instrume...

Nyc high pressure boiler license ExamQuestions and Answers. ________ is the term used with a wet absorber nozzle in relation to an incinerator? - ANSWER-slurry .(TS x t x E) / (R x FS) TS = - ANSWER-tensile strength of shell plates .(TS x t x E) / (R x FS) E = - ANSWER-efficiency of longitudinal joint .(TS x t x E) / (R x FS) FS = - ANSWER-factor of safety allowed by this subpart .(TS ...

1. The efficiency of the refrigerant cycle is affected by the operation of the condenser. of the following, a more efficient centrifugal compressor operation results from Answer: Lowering the condensing pressure 2. The heat removed from the refrigerant in a condenser is Answer: Sensible and Latent Heat 3. The refrigerant unit that you have been assigned to is being taken out of service for a major repair. You have been assigned to withdraw refrigerant for storage in suitable containers. Accord...

1 FALL 2021 CAPSTONE AIC EXAM | QUESTIONS & ANSWERS (VERIFIED) | LATEST UPDATE | GRADED A+ What would be the most appropriate means for the contractor to communicate to the project owner an unforeseen condition not identified in the soils report? Correct Answer: -Write a formal business letter When is the best time to distribute the working agenda to the participants of a meeting? Correct Answer: -About one day prior to the meeting The contractor has tasked his project engineer with...

Final Review RMO Exam Questions and Complete Solutions When instructed to start a reciprocating plant for Air conditioning the first thing to do is? A. TURN ON CHILLED WATER PUMPS AND OPEN THE BYPASS TO LIGHTER LOAD B. INSTALL LARGER FUSE TO TAKE THE INITIAL LOAD, AND THEN TURN ON THE COOLING TOWER FANS C. TURN ON CHILLED WATER PUMP, CONDENSER WATER PUMPS AND COOLING TOWER FANS D. SET THE THERMOSTAT A FEW DEGREES HIGHER - Answer: C. Turn on chilled water pump, condenser water pumps an...

15 kg/s of air are compressed from 1 atm and 300K (enthalpy of 300.19 kJ/kg) to 2 atm and 900K (enthalpy of 732.93 kJ/kg). Heat transfer is negligible. The air compressor's power output is most nearly (A) 5.6 MW (B) 6.5 MW (C) 7.6 MW (D) 8.9 MW - answer-B What is most nearly the weight in lbf if a 1.00lbm object in a gravitational field of 27.5ft/s^2? (A) 0.85lbf (B) 1.2lbf (C) 28lbf (D) 32lbf - answer-A A rocket that has a mass of 4000 lbm travels at 27,000 ft/sec. What is mo...

What would be the most appropriate means for the contractor to communicate to the project owner an unforeseen condition not identified in the soils report? A. Document the issue in the job diary B. Issue a jobsite memorandum C. Draft a construction report D. Write a formal business letter - ANSWER-D. Write a formal business letter When is the best time to distribute the working agenda to the participants of a meeting? A. As a follow-up to the meeting B. At the beginning of the meeting ...