Gas piping test Study guides, Class notes & Summaries

What is a general requirement of the location of the installation of a boiler? - ANSWERSAdequate clearance from combustile construction What temperature must the materials remain under during combustion? - ANSWERS170 degrees What is a requirement for the access of the boiler? - ANSWERSAccess for operation and maintenance must not be hazardous What is required upon installation to operate a boiler? - ANSWERSInspection and test resulting in equipment use permit from commissioner How of...

MN Boiler License Questions With Complete Solutions Graded A+ a question an answer what are the conditions necessary for good combustion? a) low sulfur content b) Thermal, thermocoupler, tubular c) turbulence, temperature, time 3T's c) turbulence, temperature, time 3T's why is secondary air necessary in hand fired boilers? a) Necessary to burn the combustible gases b) if primary air should fail c) used only if sulfur content is high a) Necessary to burn the combustible gases when ...

LP-Gas Texas Bobtail Questions and Answers 100% Pass required for all piping systems that serve _______ psig appliance systems. normally operated at 11 in WC pressure 1/2 required for all piping systems that serve 1/2 psig appliance systems. normally operated at ______ in WC pressure 11 above group LP-gas containers must not be located within ____ feet of the vertical plane beneath overhead electric power lines that are over _____ volts 6 600 Fire Extinquishers must have minimum capacity of ...

ASPE CPD Study Questions AH with complete solutions. Front - correct answer. Back What is the specific weight of water? - correct answer. 62.4 lbs per cubic foot What happens in a storm and sanitary system after it passes the water test? - correct answer. A smoke pressure test is recommended with a smoke pressure of 1 in wc to prove the system gas tight. Is an air test acceptable for a storm and sanitary system? - correct answer. Yes, if a water test is not poss...

Nyc high pressure boiler license Exam Questions with Correct Answers The minimum blowdown for a spring loaded safety valve shall be of what percent of set pressure? - Answer-10% How is the main steam pressure gages tested? - Answer-With an inspectors gage Who is in charge of the code for any plumbing installations? - Answer-The nyc plumbing code When will anchorage or guides be inspected? - Answer-Annually How many brass washout plugs does a miniature boiler have? - Answer-3 brass wa...

Test Bank For Modern Refrigeration and Air Conditioning 21st Edition by Andrew D. Althouse, Carl H. Turnquist, Alfred F. Bracciano, Daniel C. Bracciano, Gloria M. Bracciano 8776, 1, 6044, 1 1 - Careers and Certification 2 - Safety 3 - Service Calls 4 - Energy and Matter 5 - Gases 6 - Basic Refrigeration Systems 7 - Tools and Supplies 8 - Working with Tubing and Piping 9 - Introduction to Refrigerants 10 - Equipment and Instruments for Refrigerant Handling and Servic...

Defects on gas piping or fittings shall be _____.(A) repaired(B) replaced or repaired and retested(C) repaired by a certified welder(D) ignored, as the operating pressure is much less than the air test. - Answer B. Fitting shall be replaced or repaired and retested. UMC Section 1316.4.3 Every absorption refrigerating system supported from the ground shall rest on a concrete slab extending not less than _____ the adjoining ground level.(A) 3 inches below(B) 3 inches above (C) 6 inches below(...

Nyc high pressure boiler license exam with question and answers latest update The minimum blowdown for a spring loaded safety valve shall be of what percent of set pressure? - ANSWER>>10% How is the main steam pressure gages tested? - ANSWER>>With an inspectors gage Who is in charge of the code for any plumbing installations? - ANSWER>>The nyc plumbing code When will anchorage or guides be inspected? - ANSWER>>Annually How many brass washout plugs does a miniature b...

The minimum blowdown for a spring loaded safety valve shall be of what percent of set pressure? Correct Answer 10% How is the main steam pressure gages tested? Correct Answer With an inspectors gage Who is in charge of the code for any plumbing installations? Correct Answer The nyc plumbing code When will anchorage or guides be inspected? Correct Answer Annually How many brass washout plugs does a miniature boiler have? Correct Answer 3 brass washout plugs, 1" in size How often i...

What is a general requirement of the location of the installation of a boiler? - ANSWERSAdequate clearance from combustile construction What temperature must the materials remain under during combustion? - ANSWERS170 degrees What is a requirement for the access of the boiler? - ANSWERSAccess for operation and maintenance must not be hazardous What is required upon installation to operate a boiler? - ANSWERSInspection and test resulting in equipment use permit from commissioner How of...

Gas Piping Test Questions and Answers Verified by Expert 100% Correct