Ignition spark - Study guides, Class notes & Summaries

Combustible Liquid - A liquid with a flash point ABOVE 100F 12.5 - If the current flowing out from an electrical panel is 12.5 amps, and it then flows through an electrical load of 1500 watts, what is the amperage of the remaining current flow of the return circuit? 1000 - If a hair dryer draws 8.3amps (in a home with 120-volt service), what is the wattage? *Power (P) = current (I) x voltage (V) Watts = amps x volts 1987 - The year of the first edition of NFPA 1033 1.5 times - ...

NATE Gas Heating Exam Questions with Correct Answers Since 1992, the United States Department of Energy has required that all furnaces sold and installed from that date on must have an AFUE of no less than: A: 70% B: 75% C: 78% D: 80% -AnsC: 78% Many pre-1992 furnaces have efficiencies around _______. A: 10% B: 40% C: 60% D: 80% -AnsC: 60% Today, furnaces with AFUE ratings greater than _____ are available. A: 85% B: 90% C: 100% D: 110% -AnsB: 90% A thermocouple is used with: A:...

ABYC Practice Questions and Correct Answers 100% Verified A sailboat's rigging is considered a reliable path to ground for lightning? T/F? - Correct Answer FALSE. End fittings introduce the possibility of high resistance. TE-4, Conductors Gasoline engines use what kind of ignition? - Correct Answer Spark igntion Diesel Study Guide, Chapter 1 Diesel engines use what kind of ignition? - Correct Answer Compression ignition Diesel Study Guide, Chapter 1 Spark ignition are what kind of eng...

Combustible Liquid - Correct answer-A liquid with a flash point ABOVE 100F 12.5 - Correct answer-If the current flowing out from an electrical panel is 12.5 amps, and it then flows through an electrical load of 1500 watts, what is the amperage of the remaining current flow of the return circuit? 1000 - Correct answer-If a hair dryer draws 8.3amps (in a home with 120-volt service), what is the wattage? *Power (P) = current (I) x voltage (V) Watts = amps x volts 1987 - Correct answer-The y...

What is the first thing a tech should do when arriving at a no combustion call? - Answer- Ask how many times the customer reset the unit. What is the best long term solution for preventing a clogged nozzle? - Answer- -Remove any underground storage tanks. -Install a quality oil filter. -Cut the suction line 10" above the tank outlet to prevent sludge. Hot water and steam valves are interchangeable. - Answer- False When in the presence of a flame, a cad cell normally reads.. - Answe...

Ontario Gas G1 Practice Exam Prep B149.3-10 Questions and answers with 100% Complete Solutions | verified &updated 2024 What is the first action 'to be taken when performing an ignition spark response test? - Close test firing valve and pilot valve A valve not considered 100% shutoff - Butterfly valve The "Bleed" valve on a double block&bleed system is required on an appliance firing over? - Where is the low pressure switch located on the valve train? - After the main gas regulator Wher...

The basic methodology of the fire investigation should rely on the use of a ______________________ and attention to all relevant details. a. systematic approach b. approximation approach c. methodology approach d. general approach - ANSWER-a. systematic approach With few exceptions, the proper methodolgy for a fire or explosion investigation is to first _____________________ then investigate the cause, circumstances, conditions, or agencies that brought the ignition source, fuel, and ox...

Technician A says that when pressure testing a radiator cap, a special adapter is needed. Technician B says the best way to check thermostat operation is while it is in the engine. Who is right? - Tech A A technician is checking resistance in an engine's spark plug wires using an ohmmeter. A general rule is to replace a wire if resistance is over: - 30,000 ohms Technician A says that in an ignition system, the voltage supplied to the coil during starting is battery voltage. Technician B s...

NATE Gas Heating Exam Verified Questions and answers 2023 Latest Update Since 1992, the United States Department of Energy has required that all furnaces sold and installed from that date on must have an AFUE of no less than: A: 70% B: 75% C: 78% D: 80% - correct answer C: 78% Many pre-1992 furnaces have efficiencies around . A: 10% B: 40% C: 60% D: 80% - correct answer C: 60% Today, furnaces with AFUE ratings greater than are available. A: 85% B: 90% C: 100% D: 110% - correct ...

ASE-A8 Engine performance Latest 20023 Already Passed If the compression is 5 psi and the oem spec is 140 psi, what most likely is the cause? A, worn piston ring. B, burnt valve. Both A and B What most likely is the cause if the compression doesn't go up during a wet compression test? A, burnt valve. B, worn piston ring. A What most likely is the cause if the compression goes up during a wet compression test? A, burnt valve. B, worn piston ring. B 2. Blue smoke is coming from the exhaust...