Plumbing math two - Study guides, Class notes & Summaries

Plumbing Math Two Exam Questions and Answers constant - Answer-a quantity or parameter that does not change its value whatever the value of the variables, under a given set of conditions. offset - Answer-a combination of elbows or bends that brings one section of pipe out of line but into a line parallel with the other section. Pythagorean theorem - Answer-states that the square of the hypotenuse (the side opposite the right angle) is equal to the sum of the squares of the other two sides....

Plumbing Math Two questions with correct answers

Plumbing Math Two Exam Questions and Answers constant - Answer-a quantity or parameter that does not change its value whatever the value of the variables, under a given set of conditions. offset - Answer-a combination of elbows or bends that brings one section of pipe out of line but into a line parallel with the other section. Pythagorean theorem - Answer-states that the square of the hypotenuse (the side opposite the right angle) is equal to the sum of the squares of the other two sides....

Professional Home Inspector Exam 2 NHIE/TREC - Q & A (Complete Solutions) What type of roof requires on interlayment of felt between courses? a. Wood shakes b. Roll roofing c. Wood shingles d. Slate shingles In an older home, a forced hot air furnace is replaced by a heat pump. The heat coming out of the register is: a. Hotter b. Cooler c. Same d. Depends on the air duct layout When inspecting kitchen cabinets: a. Observe that they are securely attached to the wall b. Remove everything from th...

Backflow Questions and Answers 100% Accurate What is the primary consideration when deciding whether to install a reduced pressure or a double check valve assembly? Degree of hazard. A cross connection is an actual or potential connection that could allow backflow to occur between a potable water system and a piping system that contains potentially unsafe Water,steam,gases,chemicals, or unknown substances. What are two types of back flow conditions? Backpressure and backsiphona...

WGU C207 Data Driven Decision Making Quizzes & Answers(RATED A+) (Quiz 1) 1. For companies to attract and retain their best customers they need a complete portrait of who they are. To develop this portrait companies turn to... A) Statistics B) Analytics C) Management Science D) Histograms - ANSWER B (Quiz 1) 2. A manufacturer wants to maximize their factory output while specifically minimizing labor costs. What type of analytics might they employ to achieve this goal? A) Descr...

Math Applications End Of Term Prediction Questions 2024.Tamara earns $8 an hour at her job working 25 hours per week. If 22% of her paycheck goes to taxes, what is Tamara's monthly cash inflow? (Assume this is her only source of income and that there are 4 pays per month.) - ANSWER $624 Barry gets hurt at work and must go on disabililty for 4 months. On disability, the pay that Barry receives is 60% of his normal net pay. Barry should be fine if he has a plan for _____. - ANSWER managing his...

1 MODULE 4, INTRODUCTION TO PLUMBING MATH EXAM | QUESTIONS & ANSWERS (VERIFIED) | LATEST UPDATE | GRADED A+ Back Correct Answer: Part of the fitting that is opposite to the side with an opening or face. Center Correct Answer: A point exactly halfway between two other points or surfaces. Centerline Correct Answer: On a drawing, a line that shows the center of an object. Center point Correct Answer: Point created where the centerline of the pipe and the centerline of the fitting ...

Introduction to Plumbing Math Exam Questions with Correct Answers An example of a whole number is _____. - Answer-47 You have ordered a total of 15 bundles of PVC pipe. Each bundle contains 6 lengths of pipe. In total, the number of lengths of pipe in your order is _____. - Answer-90 Use the √ key on a calculator to _____. - Answer-find the square root of a number The improper fraction 14/8 can be converted to the mixed number _____. - Answer-1-3/4 3/4 - 1/8 = _____. - Answer-5/...

MODULE 4, INTRODUCTION TO PLUMBING MATH EXAM | QUESTIONS & ANSWERS (VERIFIED) | LATEST UPDATE | GRADED A+ Back Correct Answer: Part of the fitting that is opposite to the side with an opening or face. Center Correct Answer: A point exactly halfway between two other points or surfaces. Centerline Correct Answer: On a drawing, a line that shows the center of an object. Center point Correct Answer: Point created where the centerline of the pipe and the centerline of the fitting mee...