Jaygracey

ASE G1 MLR Study Guide Questions with Answers. The automotive repair process is a 6 step process. What is the last step? - Correct answer-Verify the Repair A vehicle comes in the shop with an engine noise. What should be done first? - Correct answer-Discuss the noise with the customer A spark ignition engine has a flapping sound near the front. Which of the following could be the cause? - Correct answer-Loose timing belt A tight timing belt makes what type of noise? - Correct answer-...

Quick ASE Exam Test Questions with Answers Latest Update . A hydroboost brake system has a hard pedal and reduced braking performance. Which of the following would result in this condition? - Correct answer-Aerated power steering fluid One of a vehicle's brake lights is inoperative. All other lights are functioning normally. Which of the following should be checked first? - Correct answer-The bulb results in a soft spongy brake pedal - Correct answer-aerated brake fluid is a one w...

ASE G1 General Maintenance Test Questions with Answers. Technician A says that when pressure testing a radiator cap, a special adapter is needed. Technician B says the best way to check thermostat operation is while it is in the engine. Who is right? - Correct answer-Tech A A technician is checking resistance in an engine's spark plug wires using an ohmmeter. A general rule is to replace a wire if resistance is over: - Correct answer-30,000 ohms Technician A says that in an ignition ...

ASE Study Guide - G1 Exam Test Questions With Answers. The ride (curb) height on the rear of the vehicle is found to be too low. The best corrective action would be to: - Correct answer-Replace the rear springs The role of a stabilizer (sway) bar is to: - Correct answer-Control body roll A vehicle with front disc brakes shudders when the brakes are applied. Which of these could be the cause? - Correct answer-Warped brake rotors How many amps will flow through a circuit with 3.3 ohms ...

Elaborate ASE G1 Exam Prep Questions with Correct Answers. Coolant should be tested for – a. Proper color b. Freezing point (temperature) c. Specific gravity *d. Both b and c Two technicians are discussing a compression test. Technician A says that the engine should be cranked over with the pressure gauge installed for "4 puffs." Technician B says that the maximum difference between the highest-reading cylinder and the lowest-reading cylinder should be 20%. Which technician...

ASE Auto Maintenance & Light Repair Test (Test G1) Questions With Answers. A tight timing belt makes what type of noise? - Correct answer-Whining A RWD (rear wheel drive) transmission has a leaking output shaft seal on a vehicle with 25,000 miles on the odometer. The MOST likely cause for the leakage is: - Correct answer-plugged transmission breather filter Of the following, when replacing a CV (constant velocity) joint or boot, what is the last step before clamping the boot? - Correct ...

ASE T8 Preventative Maintenance Inspection (PMI) Practice Test Questions with Correct Answers. With a cold engine, the coolant level in the radiator is too low, but the coolant level in the recovery tank is at the HOT mark. There have been no complaints of the engine overheating. Which of these could be the cause of the low coolant level in the radiator? (A) A failed radiator cap (B) A stuck-closed engine coolant thermostat (C) A stuck-open engine coolant thermostat (D) An incorrect c...

ASE G1 Test Prep (General Automobile Maintenance) Questions with Correct Answers. Toe can cause tire wear if not within manufacturer's specifications (True or False) - Correct answer-True Camber can cause tire wear if not within manufacturer's specifications (True or False) - Correct answer-True Caster can cause tire wear if not within manufacturer's specifications (True or False) - Correct answer-False Technician A says that a PAX run-flat tire uses a special wheel. Tec...

ASE: Steering and Suspension Sample Test Questions with Correct Answers. How would you adjust a rack yoke bearing? - Correct answer-Tighten, then look at OEM specifications and back off by the suggested amount of degrees. If a customer states that their steering wheel turns more to the left than to the right, what are some of the most likely causes? - Correct answer-- Incorrectly timed steering gear - Bent pitman arm - Bent tie rod A customer says that their vehicle is difficult to st...

Auto Tech ASE Prep Test Questions and Answers 2024. how many employed in automotive field ? - Correct answer-14 million define specialized tech - Correct answer-expert in one area of auto repair what does ASE stand for? - Correct answer-Automotive Service Excellence how many ASE test to become a master tech? - Correct answer-8 vehicle identification is determined by? - Correct answer-frame and chassis new test in 2013 added with high school students in mind? - Correct answer-G1...